Jump to content
SAU Community

Recommended Posts

aww my baby wont start , battery is all good when i turn the key to start it, makes a loud fast clicking sound

plz help :rofl: argh wats the problem, and how much am i looking at to fix it? or is there a cheap and easy way to fix without a mechanic :(?

Link to comment
https://www.sau.com.au/forums/topic/68344-car-wont-start/
Share on other sites

As everyone else has said, it's prob your battery. I had the same thing two weeks ago. If the batt has gone flat, you're probably looking at buying a new one, rather than trying to charge it and stick with the old one. I tried twice then bit the bullet.

It takes around 20+mins of driving to charge enough to start the car again.

To answer your q, the battery doesn't have enough charge to turn the starter motor. It is a cheap fix. Replace it with a batt that has 450+CCA if you can. Your starter motor is fine. :rofl:

Mark

edit: Sumo's thoughts are it isn't the injectors. The rationale makes sense to me. The battery is still the prob though.

Link to comment
https://www.sau.com.au/forums/topic/68344-car-wont-start/#findComment-1268340
Share on other sites

Fast clicking sound will be the starter motor solenoid trying to pull in. Have heard it plenty of times. The breakdown comes when it bridges the motor contacts and the bat doesn't have enough charge to spin it so it releases, Then pulls back in and so forth.

Cheers

Sumo

Link to comment
https://www.sau.com.au/forums/topic/68344-car-wont-start/#findComment-1268964
Share on other sites

It's basically a problem of voltage to the solenoid (not necessarily a battery problem, though).

Install a relay between the battery and the solenoid. Use the existing wire onto the solenoid to switch the relay, so that the relay supplies direct battery power to the solenoid.

Link to comment
https://www.sau.com.au/forums/topic/68344-car-wont-start/#findComment-1272889
Share on other sites

it's the battery.

Here's how to test.

Get a multimeter and a mate

Put multimeter on battery to check voltage

chance are you will get...12 volts, so you will say "SEE it's not the battery"

but then...get your mate to turn the engine over, if the voltage drops below 8v, your battery is cactus, take it to a battery shop and they will test it for you to be sure.....If the voltage holds at 10v+ then it is probably not ya battery, in which case...umm only think i can think of is you could tap the starter motor/solenoid, sometimes they jam up....

Link to comment
https://www.sau.com.au/forums/topic/68344-car-wont-start/#findComment-1272982
Share on other sites

Yeah, I wouldn't give up on the battery totally. I thought my battery was stuffed. Car had been off the road for 6 months and was completely dead when I went to crank the car. Stuck it on charge for like 18 hours and it started no problems. Drove it to the mechanics for rego., he managed to drain it completely, and said he reckoned it was stuffed. Had to jump it twice on the way home, whacked it on the charger again, cleaned the terminals and connections, and hey presto, no more problems. Like you suggested, if its still running the radio etc. it must still have some charge. From my experience with batteries, the big killers seem to be age, and running run them dead flat, then leaving it flat. If your battery is more than a few years old, its the easiest thing to change first when chasing this kind of problem.

Hope this helps,

machg

Link to comment
https://www.sau.com.au/forums/topic/68344-car-wont-start/#findComment-1272986
Share on other sites

oh, and if it is your battery like I assume, jumper cables will *most likely* NOT help. You will also need some decent (fat) jumper cables that can pull heaps of current.

I havn't tired clutch starting one with these symptoms, but seriously, just take the battery to battery world and have it tested, I am quite confident it is the problem. And it's an absolute prick of a problem that had me stumped cause it had the 12v and like u say, stereo etc works great.

Way I found out was rang a mate that works for NRMA, I was trying to find imobilisers etc etc, and he was like "it's the battery" seen it happen to more cars since (mine did it on saturday)

Link to comment
https://www.sau.com.au/forums/topic/68344-car-wont-start/#findComment-1272994
Share on other sites

ive had heaps of problems and delays with batteries. jumping from another car just made things worse for me, as it ran down that car battery too.

i ended up on just buying a cheap ($15) charger, and i woudnt reccomend it, it gave me grief for several days. at first the charge indicator (4 LEDs) worked, but then they just stopeed working, but it seemed to still be charging the battery, as it was hot and humming. several days later it still hadnt chrged it, so i swapped the battery for a tiny one i had lying around. left it on overnight and it charged it up enough to start it.

if you want to charge it, its a good idea, but dont buy a cheap charger, there crap (my one was, other ones might work) spend some extra money, and keep it for if you have this problem again! the good ones start at about 60. new batteries cost about that much, depending on where you get them.

im just so sick of batteries. they just piss me off! i had problems for months!

Link to comment
https://www.sau.com.au/forums/topic/68344-car-wont-start/#findComment-1278902
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Add to this... What blew the fuse too? If a circuit feeding power to the coils was blown, how were the coils even functioning to let the car start?   There is some seriously wrong wiring in that car for certain, and I'm betting there is some melted cables somewhere, but I can't explain the 30v either, unless there is something back feeding on that power line that has a dodgy power system and the electronics are giving it hell.
    • This is typically the case with such threads. What I cannot quite get my head around is where a reading above 12V (or 13.8 or 14.x or whatever the maximum achievable voltage might actually be in that specific car) comes from. 25V or 30V should be completely impossible. There's no way to create it. Hard to answer that question. It will literally depend on whether the current tune relies on the values as set. I'd guess it probably does. ie, the real base pressure being 49 means that the flowrate through the injectors will be higher than if it was 43.5. The Haltech's modelling should be handling that, but because it thinks the pressure is only 43.5, then..... I dunno. It should be thinking that it will be injecting less fuel with each pulse duration than is actually happening. So, something is definitely not-as-it-should-be, but specifically what that is is beyond my abilities to imagine. Someone like Dose who spends more time with Haltechs might have a better thought.
    • Bit of a late reply here as me and my wife have been really busy with new born twins. I finally got these issues fixed and it was something really stupid that caused all of this 🤦‍♂️... After alot of mucking around with trying to figure out what is causing these issues, I back probed one of the R35 coils on the power 12v supply, with the engine running it got 25v! And I thought, hang on..., this isn't normal. Measured my battery with the engine running to check for over charge from the alternator and it wasn't that. So then I dissconnected the R35 PRP coil harness and backprobed the power supply on the engine loom where the ignition coil harness connects, with the key on ignition (engine off) it measured 30v! So then I had to trace where that high voltage was coming from and it lead me to the brown relay "ECM & IGN coil relay" inside the cabin next to the ECU on the passanger wall. This relay feeds power to the ECM and ignition coils. Tried swapping it with another same relay. nah still 30v.. coming from the 2 green/white wires in the brown relay. So then I set my multi meter to the beep continuity mode and probed every fuse on the fuse box inside the cabin to try and find this high voltage power source. Wasn't any of the fuses inside the cabin. Then probed all the fuses in the engine bay and BAM, got my power source that was a 10AMP fuse called "ENG CONT". Pulled the fuse out, and what do you know... it was blown. 🤦‍♂️  So then I quickly replaced it with a new 10AMP fuse, started the car and yeah haha [insert extreme face palm]... The RPM blimping thing went away, car idles smoothly now like what it was before. I swear! I checked all my fuses with my test light twice before I created this forum thread. I think, maybe because one side of that faulty 10A fuse lit up on my test light, I must have thought it was still ok and not blown. But now I know to have both sides light up on the test light when checking fuses... I hate diagnosing electricals.... I'd take mechanical problems over electrical problems any day🤣. Drove the car around my suburb with the engine up to operating temp and it runs fine like before. However, I notice that my fuel pressure is still at 49psi. So I'm thinking this must be normal for my system as I've upgraded the stock fuel pump to a Walbro 255L/h with a constant 12v mod.  But anyway, I'm just glad to have my daily back on the road! Thanks everyone for the replies on this thread, all sorted now! One thing I want to ask you tuner guys, my base fuel pressure on the haltech main settings are set to 43.5psi from default (my tuner must have not checked the fuel pressure maybe when tuning my car?). Do I set it to what it actually is idling on at 49psi? Or just leave it ("if it aint broke, don't fix it/leave it")?  
    • The max they would go for me is 50.
    • That cannot have been a fun set of drilling. The stock "baffle" looks identical to rb26, I just cut fuel cell foam to fit the full length under the baffle.
×
×
  • Create New...