Jump to content
SAU Community

Recommended Posts

BRAND NEW TURBO KIT FOR RB20/RB25DET

SPECS:


· T3/T4 .50compressor housing, .63 exhaust housing, 5 Bolt exhaust.

· (1) 90-degree and (1) 45-degree pipe for Downpipe

· Brand new 8.7Psi Wastegate

· Brand New Dual Type 50mm BOV

· Set of Turbo accessories

· One full set Oil Line and fittings

· Oil return Line kit

. Stainless (High mount) Manifold - STAINLESS with Lifetime Warranty

Price is $1500 + delivery.

Link to comment
https://www.sau.com.au/forums/topic/68763-500hp-turbo-kit-for-rb20rb25det/
Share on other sites

The AR's for this turbo are very common for upgrades to the R32 and R33 you will obviously find your car Cumming on to boost a bit later as it is a bigger turbo you might be sacrificing any where from 300 to 500rpm to what your stock turbo would come on to boost it can handle up to 20psi as well.

Thanks

What kinda lag wud u get with that on an rb20 and what boost levels are best through it?

The AR's for this turbo are very common for upgrades to the R32 and R33 you will obviously find your car Cumming on to boost a bit later as it is a bigger turbo you might be sacrificing any where from 300 to 500rpm to what your stock turbo would come on to boost it can handle up to 20psi as well.

Thanks

I know plenty of people using Master Power turbos and making big reliable power.

very similiar to XSPower....

Its the way you install the turbo, most people that buy these turbos are on a budget therefor they usually try and install the turbo themselves and theres your problem right there, there is alot of people out there that dont know the 1st thing about installing a turbo and are on a budget and try and install themselves to save a bit of $$$, they just think they can rip the old one off and slap the new one on.

Its the way you install the turbo, most people that buy these turbos are on a budget therefor they usually try and install the turbo themselves and theres your problem right there, there is alot of people out there that dont know the 1st thing about installing a turbo and are on a budget and try and install themselves to save a bit of $$$, they just think they can rip the old one off and slap the new one on.

Most turbos that die are due to poor quality turbos like XSPower

http://www.mx6.com/forums/showthread.php?t=110947

]

The Ebay seller you bought it off

http://cgi.ebay.com/ebaymotors/ws/eBayISAP...sspagename=WDVW

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
    • What are your thoughts on this after having it for a while, worth getting?
    • Downshifts are harder on transmissions than upshifts, the input shaft naturally slows down once disconnected from the engine so the synchros aren't doing all the work. There's no "natural" tendency for an input shaft to increase RPM. Something is not right there, I don't have a great answer on what. You can try a dedicated GL4 75W90, I plan to switch to Motorcraft XT-M5-QS which is supposedly a very good 75W90 for NB Miatas which have a weirdly sensitive transmission from the factory. I would chase down why your clutch is making a hissing noise, that's not normal. It might be no big deal but in the absence of anything else to investigate I would look at that.
×
×
  • Create New...