Jump to content
SAU Community

Recommended Posts

I've just got my silvia on the road today and am making sure nothings wrong before i really start to drive it.

I know the hallmarks of a 1.5/2 way diff are noise going round corners at low speed but i've got very pronounced noise and clunking around corners and going straight at low speeds. Its most noticeable rolling at low speeds then engaging/disengaging the clutch with a little bit of throttle. The clunk is enough to be felt throughout the car and my seat. I would expect the car to have a mech diff as its fully set up for drift.

Fully stripped interior/boot and drift suspension setup are obviously going to increase the noise and vibration, but is this level of 'clunking' normal?

Diff pictured below (non-standard rear cover?).

Link to comment
https://www.sau.com.au/forums/topic/69046-mega-clunking-from-rear-2-way-diff/
Share on other sites

i have a clunking sound too... its a very light and not too deep.

similar conditions to yours, mine can only be heard during slow turns or slowly applything the

throttle.

BUT - i think i have a standard LSD, i have spoken to my mates and they have heard it too..

they reckon its NOT the diff, and more possibly the exhaust (stock) which may have worked

itself loose or something.

I notice no difference in how the car handles however... does this sound like your problem?

i'd be interested to hear what others think?

I had a 2 way in my silvia and only on cornering did it make noises, hell noises too. You could also feel the car shift sideways on itself after correcting. Not sliding either, normal driving.

I would think there is some problem with the tailshaft/diff connection if its clunking under on off throttle.

Mine is a deep 'mechanical' sound. The exhaust is attached very firmly, there is slight grinding noise due to working the surface rust off my brake rotors, and the boot rattles round a bit, but this can clearly be heard over the top.

You could also feel the car shift sideways on itself after correcting. Not sliding either, normal driving.

Yeah, that's what it feels like.

My old standard diff in the 180 made clunking noises on/off the clutch at low speeds too due to the button clutch sending shock through the tailshaft.

Yeah, that's what it feels like.  

My old standard diff in the 180 made clunking noises on/off the clutch at low speeds too due to the button clutch sending shock through the tailshaft.

that's normal then! Its all good :) Price you pay for sideways on demand..... :)

All rear drive cars have some degree of driveline slack, what you mentioned is just the normal behaviour of hardcore 2 way... amplified by the stripping you've done.

Don't forget you almost sit over the diff in an S13 if your fairly tall...

My brother's car is the same, shuddering and noises is pretty bad during low speed cornering. Was recommended to do a rebuild of the diff, with new clutch plates and all. About $600 for our 1.5 way.

I has my Kaaz two way rebuilt by this knob in Fyshwick and he put it back togeather wrong with incorrect clearances and preloads etc.

The result felt like someone was swinging a sledge hammer under my car when i turned even the slightests corner witth anything less than heavy throttle.

Even coasting into a corner in 4th or 5th would get it going.

The car dramatically changed direction between on and off throttle two.

Since having it rebulit by a decent engineer, it is perfectly smooth when driving around town under normal throttle.

If you try and do a hill start and turn at the same time it will carry on a bit until the clutch is fully out. Then it just locks up nicely and skips the inside wheel a bit.

Running a decent synthetic oil can help but over time they can loose the correct preload settings and clearances due to normal wear and tear so yours could be half way to were mine was.

My Nismo GT Pro 2 way is very clunky at low speeds ie 5kms or less. Its currently set to the softest setting, and yes its damn clunky when the clutch is out. You either have to get used to it, or get rid of it.

I put fresh redline oil in my diff when i got it (it was just run in when i put it in my car.) It has about 5000 kms on it, and its always clunky, but damn good for corner speed (hooks up way better than std), and locking the rears if i need it (take off, and compression lockups) ;)

Sorry, but AFAIK your diff should not be making any noise when heading straight.

Certainly a locked or tight diff will clunk and carry on when you are turning, this is because the outside wheel is trying to turn faster than the inside wheel, so the inside wheel skips so it turns at the same speed.

You might have stuff worn out elsewhere in your drivetrain, driveshaft, cv joints, rear axles etc etc or the diff centre may not have been aligned properly....if not get it fixed as it will be much weaker since the gears will not be engaging properly

Yeh when going straight no clunking should happen..

Mine did last week (stock gtr diff) and it got worse so we pulled it out and some bearing failed and has caused the crown and pinion to loose teeth and stuff..

Not good!

I would get the driveline looked at as Duncan mentioned.

The AUS R31 skyline is famous for clunking and carrying on just as you have described. And it definately does not have a mech LSD.

I have one as a daily driver and get the same thing. Pull into the driveway at low speed, dip the clutch and then "PHWOOMP". Drifto described it well as feeling like a sledge hammer was swung under the car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My idle is set at 950rpm though - Moving the timing around 20 degrees is not really what I'd call a calm idle. That said... neither is chop, by definition. The LS ECU likes to adjust timing to hold idle as opposed to air. It'd work, but generally speaking there'd be a discrepancy in the base idle and the IACV would want to move the timing around anyway to maintain said idle. I think I'm just going to keep the timing steady anyway. Preserve my engine mounts.  My aircon is now officially regassed. As the guy was reversing I noticed my reverse lights do not operate, along with my reverse cam. This is a bit distressing, because 100% of guides talk about which wire to connect to backup cams as "the goes with the [other color] wire". Often when doing conversions. Unfortunately the R34 colour wires aren't documented Unfortunately I had a T56 Magnum gearbox with it's reverse switch, which also isn't documented. Unfortunately there's definitely not documentation for people with both of these in the one car. Unfortunately I forgot. After many hours of this, I have a reverse cam and reverse lights again. The wire going through the trans tunnel to the reverse switch had broken. Upon inspection, it looks like this one wire had about 7 spade terminals and extensions in it.. for reasons I cannot possibly comprehend. I also spent the 750 hours required to clean up the wiring behind my head unit which now looks like this: This is a monumental improvement relative to what used to be there WRT triple gauges, head unit, traction control, wideband controller, and whatever the f**k OEM stuff still exists there in various states of connectivity/needed. Next step is to check in at the Exhaust shop to see/confirm how much clearance I have, to decide what mid mufflers or 'resonators' (which are just straight through, narrower mufflers) I can add and hopefully cut out a lot of exhaust leaks, pinhole, v-band or otherwise. But first step will be to 'take a look' before the next step.
    • Fark the AFM card and Nistune, Haltech Nexus S3, DBW, cruise control, flex fuel, dis dat.  
    • It's most likely the bolt/bush where the cover bolts back wore and allowed cover to move forward.
    • Still haven't put the injectors and R35 AFM in so we can tune the bloody thing for the HG highflow it got mid last year! I think I can forecast the upgrade path to a bigger twin scroll, external gate, Haltech, flex setup, Samsonas, dis dat, etc will be .... a while away!
    • Should have taken that opportunity to slot in a twin scroll turbo setup. Maybe next time.
×
×
  • Create New...