Jump to content
SAU Community

Recommended Posts

I've just got my silvia on the road today and am making sure nothings wrong before i really start to drive it.

I know the hallmarks of a 1.5/2 way diff are noise going round corners at low speed but i've got very pronounced noise and clunking around corners and going straight at low speeds. Its most noticeable rolling at low speeds then engaging/disengaging the clutch with a little bit of throttle. The clunk is enough to be felt throughout the car and my seat. I would expect the car to have a mech diff as its fully set up for drift.

Fully stripped interior/boot and drift suspension setup are obviously going to increase the noise and vibration, but is this level of 'clunking' normal?

Diff pictured below (non-standard rear cover?).

Link to comment
https://www.sau.com.au/forums/topic/69046-mega-clunking-from-rear-2-way-diff/
Share on other sites

i have a clunking sound too... its a very light and not too deep.

similar conditions to yours, mine can only be heard during slow turns or slowly applything the

throttle.

BUT - i think i have a standard LSD, i have spoken to my mates and they have heard it too..

they reckon its NOT the diff, and more possibly the exhaust (stock) which may have worked

itself loose or something.

I notice no difference in how the car handles however... does this sound like your problem?

i'd be interested to hear what others think?

I had a 2 way in my silvia and only on cornering did it make noises, hell noises too. You could also feel the car shift sideways on itself after correcting. Not sliding either, normal driving.

I would think there is some problem with the tailshaft/diff connection if its clunking under on off throttle.

Mine is a deep 'mechanical' sound. The exhaust is attached very firmly, there is slight grinding noise due to working the surface rust off my brake rotors, and the boot rattles round a bit, but this can clearly be heard over the top.

You could also feel the car shift sideways on itself after correcting. Not sliding either, normal driving.

Yeah, that's what it feels like.

My old standard diff in the 180 made clunking noises on/off the clutch at low speeds too due to the button clutch sending shock through the tailshaft.

Yeah, that's what it feels like.  

My old standard diff in the 180 made clunking noises on/off the clutch at low speeds too due to the button clutch sending shock through the tailshaft.

that's normal then! Its all good :) Price you pay for sideways on demand..... :)

All rear drive cars have some degree of driveline slack, what you mentioned is just the normal behaviour of hardcore 2 way... amplified by the stripping you've done.

Don't forget you almost sit over the diff in an S13 if your fairly tall...

My brother's car is the same, shuddering and noises is pretty bad during low speed cornering. Was recommended to do a rebuild of the diff, with new clutch plates and all. About $600 for our 1.5 way.

I has my Kaaz two way rebuilt by this knob in Fyshwick and he put it back togeather wrong with incorrect clearances and preloads etc.

The result felt like someone was swinging a sledge hammer under my car when i turned even the slightests corner witth anything less than heavy throttle.

Even coasting into a corner in 4th or 5th would get it going.

The car dramatically changed direction between on and off throttle two.

Since having it rebulit by a decent engineer, it is perfectly smooth when driving around town under normal throttle.

If you try and do a hill start and turn at the same time it will carry on a bit until the clutch is fully out. Then it just locks up nicely and skips the inside wheel a bit.

Running a decent synthetic oil can help but over time they can loose the correct preload settings and clearances due to normal wear and tear so yours could be half way to were mine was.

My Nismo GT Pro 2 way is very clunky at low speeds ie 5kms or less. Its currently set to the softest setting, and yes its damn clunky when the clutch is out. You either have to get used to it, or get rid of it.

I put fresh redline oil in my diff when i got it (it was just run in when i put it in my car.) It has about 5000 kms on it, and its always clunky, but damn good for corner speed (hooks up way better than std), and locking the rears if i need it (take off, and compression lockups) ;)

Sorry, but AFAIK your diff should not be making any noise when heading straight.

Certainly a locked or tight diff will clunk and carry on when you are turning, this is because the outside wheel is trying to turn faster than the inside wheel, so the inside wheel skips so it turns at the same speed.

You might have stuff worn out elsewhere in your drivetrain, driveshaft, cv joints, rear axles etc etc or the diff centre may not have been aligned properly....if not get it fixed as it will be much weaker since the gears will not be engaging properly

Yeh when going straight no clunking should happen..

Mine did last week (stock gtr diff) and it got worse so we pulled it out and some bearing failed and has caused the crown and pinion to loose teeth and stuff..

Not good!

I would get the driveline looked at as Duncan mentioned.

The AUS R31 skyline is famous for clunking and carrying on just as you have described. And it definately does not have a mech LSD.

I have one as a daily driver and get the same thing. Pull into the driveway at low speed, dip the clutch and then "PHWOOMP". Drifto described it well as feeling like a sledge hammer was swung under the car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For sure the later RB26 variants had a different setup (6 cam voltage sender?), but the RB25DE/DET share the same ECU pinout/PCB footprint, and at the ECU plug it ends up being 'throttle sensor in' & 'throttle sensor out' (to A/T TCU) ...you stick a multimeter on these pins and you'll find them directly connected (0 ohms) ; I had an pair of Nissan ECUs on the bench long ago, and I noticed this throttle sensor in/out link, actually linked to an op-amp ...which was unpopulated on the NA board, but present on the T board and I went 'ah-ha!' in some moment of clarity... ...it wouldn't surprise me if they changed strategy here though (in the software and actual monitoring of this signal), because they did with other stuff (A/T signals).. and 0.45v as a trigger point makes sense, as that's what the external TCU units expect at idle ; kudos, thanks for that insight...I suppose it boils down to whether or not Consult can display real time data of that signal's voltage... ...in any event, it presents the same target...ie; rotate TPS unit to achieve 0.45v to suit both ECU&TCU, and where do you goto from there? Just disconnect TPSwitch connector and/or that plus TPSensor connector....or do you go for the throat and disconnect IACV solenoid and see if it still stalls? (probably throws a recoverable fault code and goes for default idle strategy?)...
    • I’m also conscious that e85 is slowly being phased out. Not all United’s have them anymore. Can’t take the risk of being low on petrol and assuming the servo will have it. 
    • MR HAMMER has said his piece. Painted up to avoid Rusty Rusty. Actually lines up well. (i.e it lines up the same as the unmolested GTR guard). Turns out the GTR Strut brace does foul on the bonnet vents ever so slightly. May need a little bendy bendy if intended to keep using with a strut brace. So spacing it out to clear the FAST102 is not an option. Annoyingly, the bonnet vents also foul on the heater lines running over the engine. Given this engine does not EVER require a heater, a delete loop is going to be used. Don't worry, the defogger uses the AC. The heater is basically "Do not use the aircon and turn the fan on". It will still be effective, I promise.... once I get the system regassed... Will have to revisit with unvented bonnet I suppose, and suitable strut brace. There's plans to do this and other things tonight and bleed brakes (there was a weep) and put the bumper back on, and take Good Friday morning - Because troubleshooting on the side of the road limping it home at midnight tonight is ... not very smart.
    • Thank you all for you assistance. I contacted Nistune regarding the support for the RB20DE along with my ECU Code (23710-10U00). They do have a map for it and added the RB20DE as a purchasable option now as well. They also added Malta as a Billing and Delivery options as this was missing. I was honestly amazed at their quick response and action, it took less than 24 hours. I also looked again at direct fit options for injectors, just in case I were to replace them. DeatschWerks seem to use a Bosch EV14 base and makes ones that fit mine at 440cc lowest, but also have 550cc at the same price. I tried looking for other direct fit options and managed to find one (also Bosch EV14 based) which includes a plug and play adapter on ebay. Did a small test with a Noid Light on the troubled injectors and all seems good, so they are pulsing properly electrically. One weird part is that they are missing on the same two cylinders as before I got the injectors cleaned. Mechanic also found this weird as he did not label the injectors and it is unlikely to have the faulty injectors be installed in the same cylinders.  
×
×
  • Create New...