Jump to content
SAU Community

Cheap Hi-Flow Cat

50FFT

By 50FFT,
in Queensland

 Share

Recommended Posts

50FFT Community Regular

50FFT

Posted
  • Author
Posted

haha, yeh i have heard about cheap ones on ebay, but after the whole GTDNO thing i went through on here i would rather buy one from someone legit...I heard of some available from somewhere in Redcliffe for like $180, but dunno the name of the joint. Any help would be kool, if we can we might organise a group buy.

Matt

The Dan Grand Master

The Dan

Posted
Posted

$170 each and you can have as many as you like

3" high flow

Brand: Carsound.

Have been running 18psi and lots of hard time on this one for 2.5 years now and is still good.

My car runs rich as a muther and it is still ok

I work at Midas Woolloongabba but am currently filling in for someone at our Capalaba store.

And then you can have it fitted also.

Depending on the car and setup...fitting won't be more than $80

SmoothLine Grand Master

SmoothLine

Posted
Posted

Step One, remove cat from system.

Step two, stand cat north south over a drain.

Step three, using a hammer and screw driver, belt away at the honeycomb looking filling.

Step four, continue belting away until said honeycomb is all in the drain.

Step five, re-attach cat to system.

I did this on my secret track car, as its illegal to not run a cat on poublic roads.

Sneaker Enthusiast

Sneaker

Posted
Posted
Problem with a 2nd hand one is that the internals of the cat will be demolished by now

They should only be keeping good cats at most of the wreckers anyway. You can still get a secondhand good one if you look, just like buying a turbo. I did the same for an engine conversion about 6 years back and both are still going well. A cat can last for a long time as long as it is operated properly in the car it came from (correct fuel mixture, temperature.)

The Dan Grand Master

The Dan

Posted
Posted
Step One, remove cat from system.

Step two, stand cat north south over a drain.

Step three, using a hammer and screw driver, belt away at the honeycomb looking filling.

Step four, continue belting away until said honeycomb is all in the drain.

Step five, re-attach cat to system.

I did this on my secret track car, as its illegal to not run a cat on poublic roads.

You forgot Step 6. Get pulled over by transport inspectors who tell you your cat is hollow because of the poisonous gases bellowing out the back

and Step 7. Get fined up to $5000 depending on how 'aware' you were that it was hollow.

strutto Grand Master

strutto

Posted
Posted
You forgot Step 6. Get pulled over by transport inspectors who tell you your cat is hollow because of the poisonous gases bellowing out the back

and Step 7. Get fined up to $5000 depending on how 'aware' you were that it was hollow.

But what if there is no cat there? You can't be aware of a hollow cat if you don't have a cat now can you :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Rb25det Belts Change

      By joshuaho96 · Posted

      Everything I found online said never use it because it'll dramatically reduce belt lifespan.  No, but I have seen excessive v-belt tension cause the audible bearing noise from excessive radial load in things like alternators. So don't overdo it. Ideally you set it to manufacturer spec using a proper belt tension guage. I tried the "clicker" type gauges but those cheap things are trash. They read way too low even when you're careful.
    • joshuaho96
      HKS stroker kit step 0/1 or HKS GTIII 2530

      By joshuaho96 · Posted

      This is kind of where I've ended up for the most part. It's easier for me, easier for shops that don't have to deal with my weird criteria/picky standards, etc.
    • silviaz
      Rb25det Belts Change

      By silviaz · Posted

      Will do. Suprised if it's not the starter motor considering it's 30 years old. Will get a volt meter though. Battery is close to new.   Cheers for your help, always appreciated.
    • GTSBoy
      Rb25det Belts Change

      By GTSBoy · Posted

      This almost never happens these days. No. Clean your battery terminals and make sure they are tight. Use sandpaper on a dowel if you have to, to get oxidation off the inside of the terminals, particularly on the -ve. Check the earth cable from battery post to chassis ground and engine ground. Make sure the contact surfaces are clean - including the threads on the bolts that anchor them - because that's where a lot of the contact occurs. Wire wheel on a drill is a good thing for this. Make sure the crimps on those cables are all sound. Assuming none of that causes an improvement: Check the battery voltage after it has been resting for a while. If it's at the lower end of the range, put it on charge for a while, then see if it will crank better.
    • silviaz
      Rb25det Belts Change

      By silviaz · Posted

      I just checked my belt, it wasn't super loose but I could bend it past 90 degrees a small amount so I tightened it up and for the first time ever my car didn't crank first time, had to crank it again lol. Don't know if that was because I tightened the belt or if it's my starter motor going out (been having slow starts for some time). Coulda also been when I was recording I didn't crank the key properly and it didn't save the recording lol.   Is that a thing if you overtighten a belt it struggles to start?
×
×
  • Create New...