Jump to content
SAU Community

Recommended Posts

And you can't break traction in first gear, wtf? :wassup:

when i had 330rwkw i could :(

Denham, it was running 24 psi on 104 octane fuel.

There is a slight turbo issue with my car in that its slightly mis-matched and has a bit of surge down below, and much over 17-18psi it gets some detonation.

Not much i can do, but give it some good fuel and its a open slat. We didnt wind more boost in as i need some ignition.

thats next on the list if i want some more power on 104

  • Replies 159
  • Created
  • Last Reply

Top Posters In This Topic

when i had 330rwkw i could  ;)

Denham, it was running 24 psi on 104 octane fuel.

There is a slight turbo issue with my car in that its slightly mis-matched and has a bit of surge down below, and much over 17-18psi it gets some detonation.

Not much i can do, but give it some good fuel and its a open slat. We didnt wind more boost in as i need some ignition.

thats next on the list if i want some more power on 104

Sunocorp 104 straight or % mixed in with 98??

If will start getting expensive if you have to run 104 for daily use :(

U have standard cams, head etc dont ya?

pure 104, had to be to get over the detonation problems on PULP due to the turbo

im not using it daily like that. lol. Im dropping back to under 300rwkw for normal driving. 330-360rwkw is useless.

We were seeing what we could do with the car for salon by have a play around with some things.

We found some more limitations on the hardware i have. We'll stuff more than 24psi into it once i get my ingition sorted (which is a long way away)

Race Pace Motorsport, the one and only place ill take my car from now on.

There is no-one decent around the west/north. I've been through many workshops who just have muppets working there who dont know enough to satisfy me taking my business there.

Race Pace is about a 45mins drive... to bayswater. But my car has been going there since mid last year.

Very thankful. Its worth the drive.

does anyone know what part number or serial number is stamped into a genuine gtr conrod? are all gtr rods created equal?

Sorry, my conrods went in 2 weeks ago - can't check for you. As far as I know, the R32 & R33 GTR conrods are the same size & strength. I can't give you a definite answer, as I was only told by a couple of engineers & 2 different sellers on the forums (can't remember their names), when I bought mine. I used R33 GTR conrods in my R33 GTS-T. Not sure about R34 GTR conrods.

Someone should soon post a 100% yes or no answer for you, I'm sure.

Cheers

Chris

can anyone recommend any good engine rebuilding workshops in or around epping victoria??? r31 nismoid youre from around this area, any ideas?

P.E.T Modifications are in thomastown and have built plenty of tough and big hp Nissan engines (VLs, Skylines, GTRs, etc).

Give dennis a call on 9464 4225 and tell him Gorjan (RS500) referred you.

does anyone know what part number or serial number is stamped into a genuine gtr conrod? are all gtr rods created equal?

they should be all the same from memory.

Put em next to an RB25DET rod and you can instantly see the difference.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yuck. But it's kinda the same principle, moving timing around to make car run bad but sound good.... I went for a more spirited tuning drive to iron out a few things. Car no longer stalls, and it loved to dip RPM low when you clutch in. After tuning this (and the 4-5 tables that HPTuners/LS1 OEM ECU wants for idle air correction) it's now behaving somewhat normal. All expected because there's a new TB, new Intake manifold and that new TB which is 102mm vs 78... has an entirely different IAC passage which is smaller because ????? Unfortunately at this point I went to make further fine tuning changes to avoid it flaring up, you know... _tuning_ the HPTuners dongle died. Well to be more accurate - The USB cable died in a fashion that anyone who has ever charged a phone will recognize. After the app demanding I resync it 50 or so times (which all 'succeeded' but all failed) the device does not want to sync and I've logged a ticket with support to see if it's fixable. US Support said it was a 'storage issue' but after removing the SD card inside it and formatting it/fixing it the issue does persist. Unfortunately usually the fix is "Turn in your old dongle and pay $700 for the upgraded one" it's cheaper because I get some free licence credits I unfortunately don't need. However I'm 10 minutes down the road from HP Tuners AUS/VCM so at least I won't need to post it, and logged a new ticket for support over here. Definitely drives different. My SOTP dyno believes it's probably making 310-320kw instead of the 280 before.  It scrambles for traction a little now whereas it previously different. It drives like a bigger cam car up top even though the cam is smaller, likely due to the cam not being advanced 6 degrees. The timing is deliberately low and the fuel is very rich so who knows if this will improve on the dyno. It may, imperceptably. Also funny is removing the pineapples definitely makes the car squat more and axle tramp less. So this behavior of having more top end, squatting more, and scrabbling for traction more makes me think = more power. But I could have just been sitting on the threshold of that kind of behavior before. Time will tell if my butt dyno is calibrated right. I need the exhaust leaks fixed before dyno tune for obvious AFR related reasons - I repositioned the pipes but I'm not confident it's fully sealed even if it is better. At least the car does drive around while I cannot tweak/tune it for now. And I have aircon again. medium success!
    • Don't use that manifold. Please don't use that manifold. Sunk cost fallacy is not worth the later pain. None of these will be relevant to the change that will come from the different turbo and manifold. As in, the effect of the exhaust will be nil, regardless of what else is changed. And all the cam and fuel system stuff is not changing either way, so has no effect. The turbo and manifold (and to a small extent the wastegate)....big change.
    • Just wanted to say thank you for your input   my man (lead mechanic by trade) and I have done a heap of work as you can imagine just to make the hot side work with the dump pipe, stupid massive intake on turbo, trying to get the waste gate on was not fun.  I’m kinda getting to the point where I don’t know if I try and make this work and not throw all this cash and time away or do I scrap the lot and start again? the Apexi I’ve got was tuned for a few slight differences:   Tomei pon cams (mine are stock neo) Turbo smart 38mm external waste gate (mines 45mm replumbed) with stainless screamer pipe  3inch turbo back exhaust with high flow cat Sard 800cc top feed injectors Sard adjustable fuel pressure reg    
    • Out here E90s are the cheapest way into a sporty-ish car because everyone knows just how expensive the repairs can get. 8-10k USD for an automatic 335i. 
×
×
  • Create New...