Jump to content
SAU Community

Recommended Posts

And you can't break traction in first gear, wtf? :wassup:

when i had 330rwkw i could :(

Denham, it was running 24 psi on 104 octane fuel.

There is a slight turbo issue with my car in that its slightly mis-matched and has a bit of surge down below, and much over 17-18psi it gets some detonation.

Not much i can do, but give it some good fuel and its a open slat. We didnt wind more boost in as i need some ignition.

thats next on the list if i want some more power on 104

  • Replies 159
  • Created
  • Last Reply

Top Posters In This Topic

when i had 330rwkw i could  ;)

Denham, it was running 24 psi on 104 octane fuel.

There is a slight turbo issue with my car in that its slightly mis-matched and has a bit of surge down below, and much over 17-18psi it gets some detonation.

Not much i can do, but give it some good fuel and its a open slat. We didnt wind more boost in as i need some ignition.

thats next on the list if i want some more power on 104

Sunocorp 104 straight or % mixed in with 98??

If will start getting expensive if you have to run 104 for daily use :(

U have standard cams, head etc dont ya?

pure 104, had to be to get over the detonation problems on PULP due to the turbo

im not using it daily like that. lol. Im dropping back to under 300rwkw for normal driving. 330-360rwkw is useless.

We were seeing what we could do with the car for salon by have a play around with some things.

We found some more limitations on the hardware i have. We'll stuff more than 24psi into it once i get my ingition sorted (which is a long way away)

Race Pace Motorsport, the one and only place ill take my car from now on.

There is no-one decent around the west/north. I've been through many workshops who just have muppets working there who dont know enough to satisfy me taking my business there.

Race Pace is about a 45mins drive... to bayswater. But my car has been going there since mid last year.

Very thankful. Its worth the drive.

does anyone know what part number or serial number is stamped into a genuine gtr conrod? are all gtr rods created equal?

Sorry, my conrods went in 2 weeks ago - can't check for you. As far as I know, the R32 & R33 GTR conrods are the same size & strength. I can't give you a definite answer, as I was only told by a couple of engineers & 2 different sellers on the forums (can't remember their names), when I bought mine. I used R33 GTR conrods in my R33 GTS-T. Not sure about R34 GTR conrods.

Someone should soon post a 100% yes or no answer for you, I'm sure.

Cheers

Chris

can anyone recommend any good engine rebuilding workshops in or around epping victoria??? r31 nismoid youre from around this area, any ideas?

P.E.T Modifications are in thomastown and have built plenty of tough and big hp Nissan engines (VLs, Skylines, GTRs, etc).

Give dennis a call on 9464 4225 and tell him Gorjan (RS500) referred you.

does anyone know what part number or serial number is stamped into a genuine gtr conrod? are all gtr rods created equal?

they should be all the same from memory.

Put em next to an RB25DET rod and you can instantly see the difference.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It only looks tidy, as most of the stuff that was on the whole back wall, is now in the trailer to go to the tip, or has been shoved in my 2.2x2.4m "Spare parts room", and now I can't get to anything in there Ha ha ha I could definitely do with a bit more space, but I'd just end up with your problems I'm going to enclose the car port beside the garage, and move a lot of stuff into it I think. OR... It will be setup as a fabrication area, and the main garage will have parts storage in it. I'm not sure yet... Need some pictures of that big shed you've got with the bikes and Skyline in
    • No. I think it's gone. 😭 I think you can get body coloured ones on eBay so I think I'll get one of those... Or just hang a red ribbon from the hole and whack a TOW sticker next to it.
    • Can't say I've had a bad experience with one on my car, then again it only gets washed once or twice a year... The wheels on the other hand, get a good spray often due to my shitty dusty pads.
    • @MBS206 thats pretty neat and tidy to me!  I'll get a photo of mine when I'm out there next. It might require multiple photos to understand the scale of the atrocities though... In total I have 4 sheds of varying sizes and layouts. Main shed is 14x8, second shed is 3x8, third shed is 11x2.5, fourth shed is around 6x4.  All are pretty much full.   The main goal of my cleaning tsunami is to make the main shed predominantly car and motorbikes only. Second shed is my metal fab room (2 x bench grinders, drill press, bench belt sander, metal band saw, scrap metal storage and some of my garden tools.  3rd shed is more bigger garden stuff, storage for engine crane, jack stands, concrete grinder, concrete mixer, air compressor lives there, and it now has two 2mx2m pallet racking shelves with itemised boxes holding building stuff, electrical stuff, plumbing stuff, etc, etc.  The 4th shed is Ryobi electric ride on mower, mini boom sprayer, ancient Kubota tractor, more garden stuff!  I have got a lot of shit....  Then there's the pool house (8mx4m) and the pool pump shed (4mx4m).  I built all of the sheds over the 11 years we've been here.  The main shed was a Ranbuild kit, the rest are all custom made to fit the areas available. Building the main shed taught me a LOT as I had no idea about building anything prior to that!  I've still got one more in me. It will be my man cave which I poured the extra concrete for way back when I poured the concrete for the main shed. The idea is the Skyline will be a centre piece of the main cave once (if...) it's finished.  I told my now 14 year old son yesterday that I will 100% drive him to his year 10 formal in 2 years. Still a long way off but at least I now have a date to work towards! 🤣
    • Modern oils are amazing. Add tyres to that as well.
×
×
  • Create New...