Jump to content
SAU Community

Recommended Posts

Hey guys,

I have jsut had huge scare other day on the way to work, i was taking off at lights, and as i was listening to a favorite tune, had music up, and i didnt' realise that the rear wheels must have started to spin, i went to indicate left to get in my lane to turn off, and was entering teh nundah bypass tunnel, and as i tryed to straighten up to comtinue as normal, the car just kept on vearing towards the left right 4 the wall, so i quickly swung it over to pull it away and over corected and did 180 and teh arse end was heading straight for otehr side of tunnel,

never been so scared in my life.

i have car that it unscratched from this incident but was only like 30cm's away from hitting the wall.

i hate rain.

Just warnign u's how much it changes conditions specially with teh turbo, and keep ya tunes down in the wet too.

thank god it was all ok

Later guys

Robz

Link to comment
https://www.sau.com.au/forums/topic/69889-spun-out-my-r33-a-huge-leason-learnt/
Share on other sites

  • Replies 64
  • Created
  • Last Reply

Top Posters In This Topic

As long as you learnt from the experience dude thats the main thing.

Personally Id be also checking your tyre pressures :P As when your low on air the tyres dont do what they should in the wet. One of mine was only 3psi lower and it was being a wee bit taily, you could even see behind the car one tyre was lower on air.

Also in quiet open areas when its wet, just give it a bit, try find the limits a bit more (yeah skidpan is all well and good, but its not actual road conditions)

Yeah when I first got the car I had it fishtailing (wildly) once when I had to turn into traffic and was blocked by a parked 4wd to see if any cars were coming, eventually I just said "f*** it" and went out into the lane, there was a camry almost on me so I floored it and got round the corner and started fishtailing badly, about 45 degrees one way then the other and with countersteering got it under control.

Basically - don't hit the pedal too hard when you're turning a corner. Robz it happened to you because you were turning into the tunnel, stay off the accelerator until you get straight again and this goes doubly when it is wet.

here you go

some selective copy paste from the WRC rally site

  Quote
The thinner tyres - typically 135mm wide compared to 205mm gravel and 224mm asphalt tyres - have a wider, more open tread and smaller footprint. They may make the modern generation of low, wide rally cars look slightly gangly, but these dimensions allow the tyres to penetrate the loose snow to reach the harder, more compact base below

yeah, this is half of the reason that turbos and kids don't mix.

Something similar hapened to me many years ago in the wet. Damage was done and a lesson was learned, and it took me many years to shake off my issues with driving in the rain.

I'm glad you've learned your lesson. As Strutto said, go up to mount cotton and do some driver training as it's well worth it. also being able to "cut sick" in a controlled environment should give you some much needed experience so you can identify when your car has lost traction. if the revs and the engine noise don't match what your ass is feeling through the seat then back off. Where a lot of people run into trouble (and I know i did in the past) is when you put your foot down and the wheels start spinning unbeknowns to you and your brain thinks the car isn't responding, so you put your foot into it more. Tail end comes out then you freak out, slam your foot on the brakes (locking them) and wind the steering wheel to full lock. Once you do this you're pretty much screwed and all you can really do is hold on and pray.

Either that or boost it before the apex of a corner in the wet. It's just way too easy to do yourself permanent damage in a turbo in the wet, especially on skinny tyres.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The old manifold was quite under the GTR strut brace.  The new manifold is quite [unknown] the GTR strut brace. The GTR strut brace was needed to clear the bonnet vents. The Old strut brace will almost certainly clear the new manifold, but not the bonnet vents. The old strut brace will almost certainly clear the new manifold, and the new bonnet without vents. But I am hoping the GTR strut brace clears the new manifold :p
    • On the bright side, at least you knew that it happened and remedied before anything happened. A friend of mine just took his Fiat 124 to a shop for an oil change and they didn't tighten the oil filter housing properly. 4.5 quarts spewed out and even after refilling + tightening the cap the engine has a tick now.
    • So, more pain. The FAST manifold is a little larger than the stocker. This is problematic because there really wasn't much clearance to begin with, so going from 'barely enough' well into 'no' is sad based on the external dimensions of the thing, even though where it bolts to the head is the same. Result is the fuel rails sit a good 25mm higher, and this is a bit of an issue with the wiring that runs behind the motor, and the fuel lines, and everything else. When pushing the manifold on, it required a huge amount of force to crush wiring looms to fit it, sensors like the MAP sensor are about 1mm from the firewall, and the FPR just has to bend ABS lines to be forced into place. After some brainstorming and some sad drinking, the loom for some reason ran from the grommet behind the ABS sensor, then to the driver side head, then back to the passenger side head. So all of this was pulled back and stripped, a few wires cut and rejoined, so that the 'branch' was now on the passenger side's head as below: Before you basically couldn't see anything behind the driver head. This is much improved! The MAP sensor is now pointing up (instead of at the firewall) Brackets have been made up for the rail. The rails are for a LS1, the manifold is designed around a LS2 as it's base. Which of course has slightly different bracketry and water pump clearance, hence the mods people need to do. Should be hopefully mounted tonight. I spent money on a new FPR that is slightly more compact than my Turbosmart FPR1200. The gauge has also been moved to the rail. There's also apparently an ORB to AN Union instead of the adapter, because the ~25mm of the current adapter is going to make the difference. Provided this all goes together and arrives today, it'll be the totally not stressful attempt to start it.
    • This seems like a pointless exercise. There is no E30 availability. Ongoing availability of E85 should not be assumed. Flex-fuel is the only sensible approach, so you can use E85 when and where you can get it, 98 when that's al you can get, and anything in between as you fill it up and drain it down. And if that means replacing the pumps, fitting a flex capable sensor/ECU/whatever has to be done to these Renault shitboxen, then.....so be it?
×
×
  • Create New...