Jump to content
SAU Community

Recommended Posts

Hey guys,

I have jsut had huge scare other day on the way to work, i was taking off at lights, and as i was listening to a favorite tune, had music up, and i didnt' realise that the rear wheels must have started to spin, i went to indicate left to get in my lane to turn off, and was entering teh nundah bypass tunnel, and as i tryed to straighten up to comtinue as normal, the car just kept on vearing towards the left right 4 the wall, so i quickly swung it over to pull it away and over corected and did 180 and teh arse end was heading straight for otehr side of tunnel,

never been so scared in my life.

i have car that it unscratched from this incident but was only like 30cm's away from hitting the wall.

i hate rain.

Just warnign u's how much it changes conditions specially with teh turbo, and keep ya tunes down in the wet too.

thank god it was all ok

Later guys

Robz

Link to comment
https://www.sau.com.au/forums/topic/69889-spun-out-my-r33-a-huge-leason-learnt/
Share on other sites

  • Replies 64
  • Created
  • Last Reply

Top Posters In This Topic

As long as you learnt from the experience dude thats the main thing.

Personally Id be also checking your tyre pressures :P As when your low on air the tyres dont do what they should in the wet. One of mine was only 3psi lower and it was being a wee bit taily, you could even see behind the car one tyre was lower on air.

Also in quiet open areas when its wet, just give it a bit, try find the limits a bit more (yeah skidpan is all well and good, but its not actual road conditions)

Yeah when I first got the car I had it fishtailing (wildly) once when I had to turn into traffic and was blocked by a parked 4wd to see if any cars were coming, eventually I just said "f*** it" and went out into the lane, there was a camry almost on me so I floored it and got round the corner and started fishtailing badly, about 45 degrees one way then the other and with countersteering got it under control.

Basically - don't hit the pedal too hard when you're turning a corner. Robz it happened to you because you were turning into the tunnel, stay off the accelerator until you get straight again and this goes doubly when it is wet.

here you go

some selective copy paste from the WRC rally site

  Quote
The thinner tyres - typically 135mm wide compared to 205mm gravel and 224mm asphalt tyres - have a wider, more open tread and smaller footprint. They may make the modern generation of low, wide rally cars look slightly gangly, but these dimensions allow the tyres to penetrate the loose snow to reach the harder, more compact base below

yeah, this is half of the reason that turbos and kids don't mix.

Something similar hapened to me many years ago in the wet. Damage was done and a lesson was learned, and it took me many years to shake off my issues with driving in the rain.

I'm glad you've learned your lesson. As Strutto said, go up to mount cotton and do some driver training as it's well worth it. also being able to "cut sick" in a controlled environment should give you some much needed experience so you can identify when your car has lost traction. if the revs and the engine noise don't match what your ass is feeling through the seat then back off. Where a lot of people run into trouble (and I know i did in the past) is when you put your foot down and the wheels start spinning unbeknowns to you and your brain thinks the car isn't responding, so you put your foot into it more. Tail end comes out then you freak out, slam your foot on the brakes (locking them) and wind the steering wheel to full lock. Once you do this you're pretty much screwed and all you can really do is hold on and pray.

Either that or boost it before the apex of a corner in the wet. It's just way too easy to do yourself permanent damage in a turbo in the wet, especially on skinny tyres.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...