Jump to content
SAU Community

Recommended Posts

Hey Prank,

The timezones are a bit screwed up. It looks like it's 9 hours back. I don't know if this is a stuff up on my end but in my profile the timezone is set to the Sydney one so you might want to check this out.

Also, can you explain to me step by step how to upload my avatar. I'm having a bit of a problem getting that done. It's on my local drive.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/7-timezones/
Share on other sites

Hey Man,

I am trying to work out whats wth both of these. In admin, I have the timezones set to +10 for sydney, but its wrong ?!?

Also, I am trying to work out how to have avatars uploadable.

Sorry guys, will get to this ASAP.

Link to comment
https://www.sau.com.au/forums/topic/7-timezones/#findComment-104
Share on other sites

Ok, there seems to be an issue with the timezones, if you set your profile timezone to 15hrs behind your actual timezone, it will work. ie, my timezone is +10 for sydney and I just set it to -5 and all the times are now correct.

As for the avatar uploading, I am still working on that.

Christian

Link to comment
https://www.sau.com.au/forums/topic/7-timezones/#findComment-107
Share on other sites

yeah when i change my settings in profiles it changes the time of posts.. however in the config area in the admin section it doesnt affect it at all..?? hmm i wonder if u have to close the forums for a while to change the date there.. or maybe even the date of where the board is held affects it.. but i doubt that :P.. arghh this is bugging me

Link to comment
https://www.sau.com.au/forums/topic/7-timezones/#findComment-118
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I figured out what’s wrong. It’s something to do with the high beam wire short circuiting. When I measure the continuity with a multimeter on the headlight socket connector it gives me a continuous beeping noise when I put it on the ground socket and also on the high beam socket.  On the passenger side of the car (working side), it’s only beeping when the probe is on the ground socket. Which makes sense.  So that means it has something to do with the high beam power supply for the drivers side. How do I trace that? Is it the turn signal lever malfunctioning? The one that also controls the high beam and low beams. 
    • Hey lads just finished tidying up a gtr a bought. Originally from Sydney now living in New Zealand 
    • Hi Guys, Looking for this piece if anyone can help out.   https://tfaspeed.com/products/nissan-skyline-r33-gtr-rear-trunk-finsher-panel
    • How did you go with your problem? End up fixing it. Have a y34 aswell vq30det
    • But if I smoke test 5th cylinder it’s all ok, no leaks  when I try with 2nd it’s leaking exhaust and intake, it doesn’t come from oil dip stick.    so maybe when car was running poorly, rich or sth. Spark plugs were black and covered in charcoal or sth lookalike. could potential contamination make valves not seal properly? is there also a possibility that rb’s don’t have equal performing cooling passages  meaning back of the engine will be hotter than front. Can this cause improper wear if engine was running under load for short time? Or carbon build up could just burnt from 4-6 and is still on 1-3?   I out of my head like really. Timing is as manual crank-exhaust 47, exhaust-intake 38 at this point I thinking about give it a try and make another 500-1000km and check if anything change, if not I will most likely disassemble engine head /or whole engine and send it back to rebuild. It’s killing me     
×
×
  • Create New...