Jump to content
SAU Community

Recommended Posts

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

hey ben

i got the pieces in the mail today

will install it either later tonight or 2morrow and post up the results

cheers

Eric

p.s great seller to buy off, quick replies and even quicker delivery =)

REVIEW

Hi, i promised ben i would write a review/feedback after i installed it so here goes.

I paid my money and got the boost piece in the mail about a day later (props to a great seller)

It was extremely easy to install. If I could do it in less than 5 minutes, anyone can

Stock boost on the r34 is around 5 psi low/ 7psi high (correct me if im wrong). As the boost piece replaces the solenoid, it becomes a constant high of around 10 psi (give or take 0.5 psi). This is better than the constant ground to the solenoid as it prevents the risk of damaging it. Full boost of around 10psi comes on under 3000 rpm (probably a bit less but i'm not very good at looking at the road, speedo and boost gauge at the same time). This then drops down by about 0.5 psi to around 9.5 psi or so.

Overall, its a great purchase for those that only want a little bit of boost increase. In my opinion, its only $20 or so and definately worth it for the gain.

Cheers

Eric

I got one of these delivered last week with a similar experience to ecl only on an R33 GTST sedan. 5 mins to install, great very clear instructions and the promised result of 10psi.

And for an added bonus I went to a dyno day today and with only a catback 3" exhaust, R34 stock intercooler and the magic 10psi and I recorded 176rwkw. I am very suprised at the result as there were a couple of stock 33s there that recorded the expected mid 140rwkw for comparison. Big thumbs up. Also there was no detonation but the car was quite rich :D . Big thanks!

I have sold about 14 of these and I have had feedback from about 10 people so far. All except 2 have held 9-10psi as they requested, however 2 people that have had automatics have been seeing around 13-14psi!! I am in the process of sending them more conservative ones.

I find this strange but if I find this to be consistent trend then I will have to have a manual one and another for automatics...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I vote go red. Only because I hate keeping gloss black clean. Was no worries helping out either! Glad you've survived the rain outs of QLD
    • I would again like too thank Matt for his help in me sourcing the detachable hard top for the little red car, without Matt's assistance in inspecting it and locking it down, I can guarantee it would have sold before I could get up to see it,  and as that was the only available NC hardtop in Australia, I consider myself extremely lucky on multiple levels To say I'm more that happy would be an understatement And, it is 100% water tight, I drove through torrential rain coming back south, and by torrential, they type of rain that doing 40kph in a 110kph zone was a real thing, and even then, the standing water on the Hwy was deep enough to throw waves I'm also more than happy that the huge "BEASTS" that Matt calls dogs didn't eat me for lunch, I'm sure the sniffs and licks were more to "taste test" me, over being to friendly Now to work out what colour to get it painted, panel match, or gloss black........first world problems are real
    • Actually I might have figured out. Looks like there is a tab according to google images but it's hidden. Silly me.
    • No clips on this one like the other connector. Only that red tab that I can push slightly up.
    • For any loom connector that has an obvious release that resists pushing far enough to unclip, just spray some silicone lube into it. You might also benefit from using a bent screwdriver or small pick to push in the right place at the right angle.
×
×
  • Create New...