Jump to content
SAU Community

Recommended Posts

no. it gets hot from the heat soak. ie from the engine heat. Yes this will heat up the air inside it. But very very minimally, since the air inside the piping is moving very fast, the heat from the pipes would not have enough time to heat the air inside.

basically the colder the air the better. as colder air is denser ie. same volume but more oxygen. more oxygen the better for the combustion process.

Link to comment
https://www.sau.com.au/forums/topic/70244-cai-fmic/#findComment-1297639
Share on other sites

Ok, if the intake air with CAI is say 30 degrees, the turbo heats it to 60 degrees, the intercooler might cool it by 15 degrees say, ending with 45 degree air going into engine.

If no CAI, the intake air may be 55 degrees, the turbo heats it to 85 degrees, the intercooler might cool it by 15 degrees, ending with inlet temp of 70 degrees.

It wont combust

Link to comment
https://www.sau.com.au/forums/topic/70244-cai-fmic/#findComment-1297640
Share on other sites

the cooler the air to start with the better.

The Intercooler can only take so much heat out of the air. So by giving it cooler air to start with you make its job easier. There for it can cool the air that little bit more again over what it would be if you didn't have the CAI.

Think of it this way.

Hot air in > Intercooler cools it down but a section of the intercooler heats up.

More hot air in > Intercooler cools it down. Bit more of the intercooler heats up. Less cool area for the airflow to go over to bring down the temp air temps.

MORE hot air in > Cooler has been working so hard to bring down the temps for so long its now a heatsink.

If you start with colder air you prolong this from happening for as long as possible.

If you have a really good CAI it may never happen to you.

Link to comment
https://www.sau.com.au/forums/topic/70244-cai-fmic/#findComment-1297648
Share on other sites

if u have a intercooler, y do u need cold air induction?

The answer to your question is no, but CAI may help reduce inlet temps.

The car spontaneously combusting was a joke,

and

Ok, if the intake air with CAI is say 30 degrees, the turbo heats it to 60 degrees, the intercooler might cool it by 15 degrees say, ending with 45 degree air going into engine.

If no CAI, the intake air may be 55 degrees, the turbo heats it to 85 degrees, the intercooler might cool it by 15 degrees, ending with inlet temp of 70 degrees.

It does not work like this, heat transfer is not a linear relationship. If you increase the turbo inlet temp by 15 degrees, the engine inlet temps (after the cooler) will not increase by 15 degrees. The higher the temp the faster the heat transfer, it is basic heat transfer theory.

Link to comment
https://www.sau.com.au/forums/topic/70244-cai-fmic/#findComment-1297812
Share on other sites

The answer to your question is no, but CAI may help reduce inlet temps.  

The car spontaneously combusting was a joke,  

and  

It does not work like this, heat transfer is not a linear relationship. If you increase the turbo inlet temp by 15 degrees, the engine inlet temps (after the cooler) will not increase by 15 degrees. The higher the temp the faster the heat transfer, it is basic heat transfer theory.

Yeah i know this but i was just trying to keep it simple to understand.

Maybe i should have just said CAI=good, No CAI=bad.

Link to comment
https://www.sau.com.au/forums/topic/70244-cai-fmic/#findComment-1300263
Share on other sites

The answer to your question is no, but CAI may help reduce inlet temps.  

The car spontaneously combusting was a joke,  

and  

It does not work like this, heat transfer is not a linear relationship. If you increase the turbo inlet temp by 15 degrees, the engine inlet temps (after the cooler) will not increase by 15 degrees. The higher the temp the faster the heat transfer, it is basic heat transfer theory.

I was going to say the same thing. Guess I don't have to now. :)

Link to comment
https://www.sau.com.au/forums/topic/70244-cai-fmic/#findComment-1301431
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, pretty much what you said is a good summary. The aftermarket thing just attached to the rim, then has two lines out to valve stems, one to inner wheel, one to outer wheel. Some of the systems even start to air up as you head towards highway speed. IE, you're in the logging tracks, then as speeds increase it knows you're on tarmac and airs up so the driver doesn't even have to remember. I bet the ones that need driver intervention to air up end up seeing a lot more tyre wear from "forest pressures" in use on the highway!
    • Yes, but you need to do these type certifications for tuning parts. That is the absurd part here. Meaning tuning parts are very costly (generally speaking) as well as the technical test documentation for say a turbo swap with more power. It just makes modifying everything crazy expensive and complicated. That bracket has been lost in translation many years ago I assume, it was not there.
    • Hahaha, yeah.... not what you'd call a tamper-proof design.... but yes, with the truck setup, the lines are always connected, but typically they sit just inside the plane of the rear metal mudguards, so if you clear the guards you clear the lines as well. Not rogue 4WD tracks with tree branches and bushes everywhere, ready to hook-up an air hose. You can do it externally like a mod, but dedicated setups air-pressurize the undriven hubs, and on driven axles you can do the same thing, or pressurize the axles (lots of designs out there for this idea)... https://www.trtaustralia.com.au/traction-air-cti-system/  for example.... ..the trouble I've got here... wrt the bimmer ad... is the last bit...they don't want to show it spinning, do they.... give all the illusion that things are moving...but no...and what the hell tyre profile is that?...25??? ...far kernel, rims would be dead inside 10klms on most roads around here.... 😃
    • You're just describing how type certification works. Personally I would be shocked to discover that catalytic converter is not in the stock mounting position. Is there a bracket on the transfer case holding the catalytic converter and front pipe together? If so, it should be in stock position. 
    • You talking about the ones in the photo above? I guess that could make sense. Fixed (but flexible) line from the point up above down to the hubcap thingo, with a rotating air seal thingo. Then fixed (but also still likely flexible) line from the "other side" of the transfer in the hub cap thingo up to the valve stem on the rim. A horrible cludge, but something that could be done. I'd bet on the Unimog version being fed through from the back, as part of the axle assembly, without the need for the vulnerable lines out to the sides. It's amazing what you can do when you have an idea that is not quite impossible. Nearly impossible, but not quite.
×
×
  • Create New...