Jump to content
SAU Community

ATT all R34GTT owners, please HELP !!

West

By West,
in Engines & Forced Induction

 Share

Recommended Posts

West Grand Master

West

Posted
Posted

Hi all, basicly my mate just bought a 34Gtt. The thing runs smooth and nice only recently its start to play up a bit.

Everynow and then i'll put itself on a LIMP MODE, TCS off logo come on also with Engine light and another one which i forgot. Running like a pig, sound like a subaru LOL then i'll go away in 4,5 mins.

Anyone ever suffer this before? Just to help a bit the car has HKS front mount, HKS silent zorst all the way apart from that everything is standard.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/70314-att-all-r34gtt-owners-please-help/
Share on other sites
SS8_Gohan Grand Master

SS8_Gohan

Posted
Posted

is it manual? and by limp mode do you mean you can't rev it past a certain RPM?

my car is doing the exact same thing, but i can rev it to whatever i want. 'TCS OFF' and 'SLIP' lights (means that traction control is temporarily unavailable) 'Engine' light is on too... haven't done diagnostic. I disconnected the -ve batter terminal overnight to reset the ECU, but that didn't help. I know exactly what you mean by the suby comment.

i think my car and your mates need to go do a Nissan dealer to run a diagnostic, see what the engine light is on for. Tell him/her to try the reset ECU thing, but if not.... take it to a dealer. Seems to be a fairly common problems with the GT-T's.

Bass Junky Grand Master

Bass Junky

Posted
Posted

Yeah happened to me too for a while.

Hasn't done it for ages though.

The engine splutters a little and then comes good.

I just shut the car off, started it again and it was all good.

666DAN Grand Master

666DAN

Posted
Posted

Running like a WRX is because of one of the coils packs not firing, it's the most frustrating sensation you can experience!!! I'm guessing Error 21

The coil packs in R34's are known for breaking if you look sideways at them

Downforce Grand Master

Downforce

Posted
Posted

Never had this problem on my car, it's always had a nice amount of torque... has the car had a service recently? Checked the oil levels? fuel filter? how old are the spark plugs? just some things to check out.... I'd take it to a Nissan Dealer for a diagnostic too. Good luck!

I disconnected the -ve batter terminal overnight to reset the ECU, but that didn't help.

FYI... you dont need to disconnect the battery overnight to reset the factory ECU... just disconnect, pump your brake pedal a few times until it's hard. Reconnect battery and start up, you will notice the reset has occurred.

666DAN Grand Master

666DAN

Posted
Posted

It's your canister purge control valve, best bet would to be to contact Nissan NZ...I personally find Nissan AU to be useless. It will probably still end up being ex Japan though.

It looks repairable, if you don't want to though, try here [email protected]

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Well, this is probably where a wiring diagram and a multimeter come into play.
    • Jarsky
      gauge needle removal

      By Jarsky · Posted

      I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Jarsky
      R33 GTST Axles

      By Jarsky · Posted

      Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Jarsky
      R34 Speedo not working after manual swap

      By Jarsky · Posted

      Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...