Jump to content
SAU Community

How to fix centre console latch.

thommo

By thommo,
in Tutorials / DIY / FAQ

 Share

Recommended Posts

thommo Mentor

thommo

Posted
Posted

Hey all,

Anyone else got a broken centre console latch?

You know, the little button you press to open that compartment behind the hand brake that you rest your left elbow on??

I have found on both my R33's that these were broken and didn't realise how annoying it had been till I fixed them.

Here's how I did it -

WHAT YOU WILL NEED - All you will need is a medium sized safety pin, Phillips head screwdriver and a pair of pliers.

TIME – 10 minutes.

DIFFICULTY – Piss easy! I reckon I could teach a monkey to do this.

STEP 1.

Remove console lid by undoing the 3 screws that go down into the console.

This may require a little gentle jiggling to clear the hinge springs after the screws are removed.

You should have the lid as in pic console01.

STEP 2.

Remove hinge from lid (3 screws) and all the screws (8) holding the plastic underside of the lid in place.

This will allow you to take out the latch, removing the broken bits of plastic that have been rattling round in there.

Refer pic console02.

STEP 3.

Find a medium sized safety pin, make sure that the size of the hole part on the pin is a snug fit over the latch pivot (pic console05).

Cut the head and point of the pin off, and bend with the pliers as per pics console03 & console04.

STEP 4.

Place pin within the latch as shown in the rest of the pics, then trim the pins top arm to be close to flush with the face of the plastic (pic console06).

STEP 5.

Put everything back together.

You should now have a nice firm feeling, spring loaded latch.

Hope this helps! :spank:

post-12522-1123161356.jpg

post-12522-1123161509.jpg

post-12522-1123161733.jpg

post-12522-1123161767.jpg

post-12522-1123161838.jpg

post-12522-1123161995.jpg

post-12522-1123162040.jpg

Link to comment
https://www.sau.com.au/forums/topic/70913-how-to-fix-centre-console-latch/
Share on other sites
  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

4door_Sleeper Veteran

4door_Sleeper

Posted
Posted

Fantastic.

I went to Nissan to order a new catch, and was told I had to order a whole new lid ($80). I was just about to ring back and confirm the order when I saw this post. Thanks a lot.

thommo - I owe you a beer next time your in Adelaide.

thommo Mentor

thommo

Posted
  • Author
Posted
Fantastic.

I went to Nissan to order a new catch, and was told I had to order a whole new lid ($80). I was just about to ring back and confirm the order when I saw this post. Thanks a lot.

thommo - I owe you a beer next time your in Adelaide.

hehe, i will dead set hold you to that mate :P

Frunknmont Experienced

Frunknmont

Posted
Posted
Fantastic.

I went to Nissan to order a new catch, and was told I had to order a whole new lid ($80). I was just about to ring back and confirm the order when I saw this post. Thanks a lot.

thommo - I owe you a beer next time your in Adelaide.

$80? I called my local Nissan dealer and that quoted me $170 or something for a new lid assembely. So Thommo :)

pinoi_boi_r33 Community Regular

pinoi_boi_r33

Posted
Posted

ah tommo y didn't you come earlier, i pikt up a new lid from the wreckers. the way i did it was wedge a folded up piece of paper in between the latch and lid part. sometimes the lid still came up and i miss shifted a few times into third because my arm hit the lid and i couldn't pull the gear stick right back. Cheers.

  • 2 months later...
  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By TurboTapin · Posted

      Touché. I had not noticed it was an NA. 
    • bcozican
      R32 Gtst - Track Car

      By bcozican · Posted

      it takes so long to get things done but ... they are nearly there and we hitting the track soon again  So - at Perth Festival of Speed the car unfortunately had a decent off, wasnt me driving, wasnt the person drivings fault. Long story short car got sent very fast towards the wall without the control on throttle from the driver input and a disaster was averted but there was damage that needed to be fixed - carbon busted and alot of bent bits The splitter got munched and had to go back to get fixed - took a bit to get it there, fixed and back but got a surprise package when a new double element higher DF splitter came back - nice surprise !  and first person to have one     At a car show I took the car too some punks stole one of my carbon indicator blanks and stomped on the other so had to get a new set of headlight / indicator combo from tops stage so got front fender vents as well to put in the order     While all this was happening the new MCA golds turned up and did some fiddling around with those   Put in the flappy paddle system and clutch lockout wiring/ system   We have also put shorter gearing in top top it out at 300 kmph in 6th gear  where previously I held 5th to 282 at SMP and 277 in Perth   Looking for better control and faster acceleration     I wasnt intending on doing pedal box I was managing with the brake master replacement system I had going on and adjusted std pedals but on applying the clutch switch to the old system we found the *insert technical word here * bar that goes from the pedal to the master was bent about 40 deg and about to snap = lucky find otherwise be a bad bad time - discussion was had about getting a custom bar built to withstand the load but in reality it was time      making any suspension, wheel or anything adjustments to date has been a nightmare - aero off, adjust, check and repeat - time consuming and hard - short of going full airjack system we fashioned some external manual car lifts this will make life a million times easier     All the bent framing, some intercooler pipes and other has been fixed and replaced and after 6 months I finally have the car back at home in my control so its get to work on it, set ride heights, wheel align and will start track testing again soon   So ultimately other than a few flashy bits nothing actually looks likes its been done but in reality alot has. Typical   We'll see how all this goes        
    • Duncan
      The Cool Tools Thread

      By Duncan · Posted

      I'm far from an expert, but for sticking bits of metal together occasionally I got a MIG, the biggest one I could get with a 10a plug (because while I have some 15a GPOs around, they are not everywhere).  Also, because I get through SFA, I just buy the small disposable gas bottles at Bunnings, I'm not opening a BOC account to get through 1/10th of a full size bottle each year
    • WMDC35
      SR20 to cefiro

      By WMDC35 · Posted

      FWD is different though.
    • MBS206
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By MBS206 · Posted

      Ignore the BOV / recirc valve question. You have an NA and shouldn't have one. If there magically is one though... It should be removed, though it shouldn't really effect it in the way one will for a turbo motor with it venting to atmosphere while running an afm.
×
×
  • Create New...