Jump to content
SAU Community

Recommended Posts

Hi all

This afternoon I went to the trouble of cleaning my iridiums and regapping them as the car has a slight miss above 4k revs on high boost. I thought re-gapping the plugs to .8m may make it go away. On low boost the car has HEAPS more grunt, but when you switch it to high boost it is actually worse. Very bad miss mainly around 5-7k. What is the reccommended gap to stop the missing? Its either plug gap or coils, but I dont think its the coils as the missing got worse :headspin: after the re-gap.

Any thoughts or suggestions/reccommendations?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/70998-miss-at-high-revs/
Share on other sites

How much boost are you running? What engine and mods?

I have Iridiums gapped at .8 and have never had any misses throughout the rev range on my RB25. I bought my plugs pregapped at .8 and they havn't moved in 12 months or gotten excessively dirty even after running a 10% toluene mix.

You may have damaged the Iridium tips when you cleaned or gapped them?

Try a new set of copper plugs gapped at .8, its alot cheaper that getting new coils.

going to try .7 too see if it works. tried 1.1 which is the factory setting on the iridiums in the NGK book at work. That really sucked ass. Will let you know how the .7's go. I will also be trying some of the old plugs that i have to see if its a ****ed plug.

By making the gap smaller you are just hiding that fact your ignition system cannot ignite the larger gap of spark. Bigger spark means bigger power. I had to gap my down to .65 with the stock ignition system (obviously they where faulty) but now with spitfires, ive increased my gap to .9. Also the stock ECU maybe dumping too much fuel in for the plugs to fire, hence the miss. Check it out on a dyno for A/F ratios

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok gotcha, so one post to fpr  another to bov  and I have the mishimoto boost controller and a link g4+ so I’d just have the tuner set it up properly. For the last two from plenum post throttle to  ecu/ boost controller, I know that I have a hose coming from the ecu that I was confused about so I assume that’s what connect to the boost controller from the ecu? And then the last is just from plenum to boost controller then to wastegate?
    • From there, it was just a quick electrical check, prime the oil and start her up Which, is not what happened. 1. Bloody seppo Aeropro battery holder. Not only was it too tall for the battery (which I'll forgive them for, I have another battery the same nominal size that is taller than Neil's one, but the bracket is a fixed height so the battery was spaced up) But the thing that really shits me is the hardware to hold it on requires a 7/32 Hex key. WTF. No-one will ever be able to remove or install the damn thing without a hex key they don't own 2. Kill switch no longer worked once the console was installed. Neil mentioned above he had to adjust the length but it no longer cleared the console once installed. Sorted. 3. Suspiciously, the brake light holders were hanging in the boot with no globes. Sure enough the stopper on the brake pedal was missing so they are always on unless the kill switch is activated. Will pick one up tomorrow (turns out 32 and 33 don't use the same stopper) 4. All that sorted, I turned on the kill switch, turned the key to ACC. Nothing. Turned it to IGN. Nothing. Checked some fuses and found the main IGN in the boot was missing which improved things once it was replaced. Now ECU and dash lights turn on with IGN but still no fuel pump. 5. Turned it to Start....ECU on, no fuel pump, no starter. Plus the voltage dropped straight to 9v.  I suspect the starter is f**ked but am going to have to work through it all and see what is happening, really looks like more than one issue. Does anyone have the R33 fuse box key with the circuit it sources from (eg BAT, ACC, IGN, SRT etc) and supplies? I can find a translated list showing Amps and circuit without supply circuit, and I can find supply circuit without Amps and target circuit.
    • 3rd time lucky, the AAC is now all plumbed up after getting some final fittings All set up under the plenum of maximum access
    • OK, so the weight has been bugging because it was really low. I did it again today and got a more believable answer at 1246 without driver And with a 93kg driver I'm pretty sure the car was still slightly on the quickjack last time meaning the full weight was not on the scales  
×
×
  • Create New...