Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

ive driven a fair few different model skyline's.....and i own a GTS-4 so i may be biased but i would never choose a GTS-t over the -4. they have many similarities to the GTR but without the hot price tag. And the good thing about the R32's is that the 4WD is run by a fuse so a switch can be hooked up easily to swap from rear wheel drive to 4WD instantly. good for drifting and racing. all round winner in my eyes.

***cheers***

Link to comment
https://www.sau.com.au/forums/topic/71088-r32-gts4/#findComment-1330057
Share on other sites

Hi, the 4wd system operates the same - it is Attessa, i.e. uses loss of traction and g-force sensors to activate 4wd. The V-spec and maybe normal GTR 4WD may come on faster as the car has more power to cope with when it loses traction.

Reliability is good, get the car checked out by someone who knows GTRS/GTS4's.

Parts arent too bad, as parts for GTR are fairly common these days. Good thing about parts is that it is very similar to GTR and as NIssan in Australia has to stock the GTR parts it means any parts you have to get from Nissan that are the same as the gtr dont attract freight charges.

When you are looking for high performance parts it is easier to get them for a GTR than a GTST, sometimes parts makers dont do the GTST but they DO do the GTR.

RB20DET is a good engine and can handle hard driving if serviced regularly and if modified - done properly!

On a dry track at QLD raceway I was even with a GTST which was stock like mine, I was handicapped by the extra weight and him by loss of traction. If it had been wet...

They can do with a bit of extra power as the 'competition' these days has got greater Kw, they finally caught up.

tried against some mates cars, mine stock 1990 GTS4 except for 3 inch cat back exhaust.

Against a supercharged 3.8 holden commodore(2000) model, I got beaten from start(started on 1500 rpm - got jumped!), from rolling start was neck and neck, come to a corner and its all over.

against a 220 kw v8 ss auto (2001) from standing start right on his butt, he could not pull away.

I am happy with the performance until I get in my friends GTR!

I know a guy on skylines downunder who has a GTS4 with 280 kw from his RB20det - lots of mods and lotsa $$$

Link to comment
https://www.sau.com.au/forums/topic/71088-r32-gts4/#findComment-1335018
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've been building a 26/30 for a few years now. I've had the head built with all the good stuff. I had a 32 gtr but blew it up and yes its all going into a vl but im looking for some advice from some RB nuts on pros and cons on putting a 26 head on a 30 bottom end is it worth it Works are as follows Head -Extensive porting 1mm oversized supertech valves Supertech double springs Supertech valve guides Supertech titanium retainers Tomei solid lifters Tomei 270 x 10.25 cams Head drain Bottom end series 2 rb30 block Cp ceramic coated pistons Eagle rods Romac balancer Oil restrictions  O ringed blah blah spent a fortune And will get a girdle because the 30s arent used to handling that much rpm Nitto billet oil pump Hypertune plenum 6boost mani Refurbed astra pump thats the cover for it in the boot I did have a precision 6262 but sold it because drag car life. Currently building the ass end full 4 link floater rear end with a 2 speed  But the dilemma i have is my mate rekens I should just stick with the 30 head for reliability. Has any one had any issues with mounting the 26 head ie compression blowing gaskets etc. Just looking for some advice from people who have gone down this route. Here's some photos. Blew the oil pump in the gtr and decided to rip the motor out at the time and do a full build only to find it had been a repairable write off so went down this path.     
    • I've been building a 26/30 for a few years now. I've had the head built with all the good stuff. I had a 32 gtr but blew it up and yes its all going into a vl but im looking for some advice from some RB nuts on pros and cons on putting a 26 head on a 30 bottom end is it worth it Works are as follows Head -Extensive porting 1mm oversized supertech valves Supertech double springs Supertech valve guides Supertech titanium retainers Tomei solid lifters Tomei 270 x 10.25 cams Head drain Bottom end series 2 rb30 block Cp ceramic coated pistons Eagle rods Romac balancer Oil restrictions  O ringed blah blah spent a fortune And will get a girdle because the 30s arent used to handling that much rpm Nitto billet oil pump Hypertune plenum 6boost mani I did have a precision 6262 but sold it because drag car life. Currently building the ass end full 4 link floater rear end with a 2 speed  But the dilemma i have is my mate rekens I should just stick with the 30 head for reliability. Has any one had any issues with mounting the 26 head ie compression blowing gaskets etc. Just looking for some advice from people who have gone down this route. Here's some photos. Blew the oil pump in the gtr and decided to rip the motor out at the time and do a full build only to find it had been a repairable write off so went down this path.     
    • lol no cats running str pipes … might put the high flow back on but I suspect it might effect my ignition timing a bit. 
    • That looks a bit like yellowing to me. If the rear bar was looking like that from rich idle, I'd ask the question, do you have a catalytic converter fitted, and fully working?
    • Oh yeah gets really bad down here. I’ll have to upgrade the heater and wind screen wipers as well for optimal performance.
×
×
  • Create New...