Jump to content
SAU Community

Recommended Posts

was looking into some balancers and this was mention to me

WE NOW HAVE A BONDED BILLET STEEL BALANCER THAT IS A WILD CARD. FOR THE RACER WHO NEEDS A BALANCER FOR HIS TRANSPLANT AND WHO CAN LIVE WITHOUT POWER STEER AND A/C. THE BALANCER COMES WITH A SAFETY SHIELD THAT BOLTS ON THE FRONT. THIS SHIELD IS MANDATORY FOR CARS THAT ARE DOING THE ¼ MILE IN 12 SECS OR LESS. IT PREVENTS THE OUTER FROM LEAVING THE ENGINE IN CASE OF A RUBBER FAILURE.

there are lots of cars that have ran 12s and i dont think its an issue....what if you runs 11s and 10s does the scrutineering get tougher?

Link to comment
https://www.sau.com.au/forums/topic/71168-harmonic-balancers-question/
Share on other sites

s15s are wicked...but they make it into the 11s not 12.0@245rwkw cough cough 330rwkw + nos  :headspin:

Hey I wasn't talking to you, I was talking to gtrsux.

I think what you are trying to say, is that cast harmonic balancers (schtandard) are not approved by ANDRA, and that an SFI approved balancer(billet/forged/aftermarket) is preferred. But check out the Compak Attak thread, if they let a car slip onto the podium 200lbs underweight what makes you think they will nit-pick balancers? Unless you are going to try and blackmail them?

Guest two.06l
Hey I wasn't talking to you, I was talking to gtrsux.

I think what you are trying to say, is that cast harmonic balancers (schtandard) are not approved by ANDRA, and that an SFI approved balancer(billet/forged/aftermarket) is preferred. But check out the Compak Attak thread, if they let a car slip onto the podium 200lbs underweight what makes you think they will nit-pick balancers? Unless you are going to try and blackmail them?

solve all the problems.....run an N1 balancer.....billet steel

good enough to get our race car ANDRA tech'd

Theo runs one as well..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Probably a smart choice to buy one vs build, purely for the motivation part as you said! Imagine the metal dust everywhere from grinding all the steel to build one. Ha ha ha!   Also, post a photo of your garage.   Mine is below, this is where I've been cleaning and have already half filled a caged 6*4 trailer. And this is after my cleaning expedition mentioned previously... The middle normally has a car in it, but I'm dumping things in the middle as I sort through them. And poor skyline was dusty and has had the lightest few drops of rain and now it looks atrocious and needs to be dragged back out and washed thoroughly! And yes to the right is technically another bay, you really can only see 2 bays out of 3 in this picture.  
    • It's more like on average the things I see a lot of things going wrong. Yes, usually the people who reach out are the ones who are having problems but on average it feels like mechanics and tuners here aren't really competent. I swing between thinking my standards are just way too high and wondering whether people really are just this dumb. I just had the strangest 10+ reply argument on a Facebook group over someone insisting that the factory R34 GTT boost control solenoid reduces boost pressure to 5 psi when it's on and raises boost pressure to 7 psi when it's off despite showing the exact plumbing in the factory service manual and the solenoid behavior detailed in the FSM.
    • I steam cleaned my near new set of volk gtc wheels 14 years ago and farrkkked them lol. The clear coat cracked like spider webbing in several areas. Lesson learnt don't do that. 😭
    • If you don't touch the CAS, then you're fine.
    • Yeah, my moulds and seals are 32 years old now. I think I will continue to not use a pressure washer on it.
×
×
  • Create New...