Jump to content
SAU Community

Recommended Posts

Hey,

Do R33 GTR N1 turbo's have ball bearing cores?

Found these on a site, anyone know if these are correct?

compressor housing: type T3, A/R 0.42,

compressor wheel: type T3, trim 55T

center housing: type T25, bearing F/M360°

turbine housing: type T25, A/R 0.64

turbine wheel: type T25, trim 62T, Fins 11

Cheers

jono

Link to comment
https://www.sau.com.au/forums/topic/71939-quick-question-about-n1s/
Share on other sites

Guest two.06l
Hey,

Do R33 GTR N1 turbo's have ball bearing cores?

Found these on a site, anyone know if these are correct?

compressor houseing: type T3, A/R 0.42,

compressor wheel: type T3, trim 55T

center houseing: type T25, bearing F/M360°

turbine houseing: type T25, A/R 0.64

turbine wheel: type T25, trim 62T, Fins 11

Cheers

jono

only r34 n1's are bb core. Well to the best of my knowledge they are anyway.

only r34 n1's are bb core. Well to the best of my knowledge they are anyway.

Thats what I thought too. Just that i've been talking with a guy selling some 33N1's and he's positive they are ball bearing cores. hmmm ..how to find out..

Only the 34's were BB  

If the person selling them is still convinced they are BB take the turbos down to GCG and ask them to look over them and give you an independant answer. They normally don't charge you anything to give them a quick once over.

I'd like to do that, only drama is that the turbo's are in QLD. Might get a mate up there to drop them at a turbo specialist :)

GTR032  

I think they are the same as my n1's im fairly sure their not BB.

ask what serial number is on them..  

Standard GTR Turbo:  14411-24U00

R33 N1 Turbo          :  14411-24U10

You've had these same spec N1's on a GTR? How'd they run? Any power figures and boost peak rpm levels?

thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wiring the car up today so will report back for anyone else that searches this in future.
    • The light comes on from low oil pressure. Not temp. Did you do a rebuild or just add an ecu etc?  What oil are you using and where are you getting the pressure reading from
    • So like the title says my 97 rs4v has a oil temp sensor but no triple gauges as it was originally factory navigation. My current setup is not using the factory oil pressure sensor as I'm running a link ecu and a real sensor.  I did leave the oil temp sensor in. So now as I was working on first start up and bleeding coolant I get the oil light on the dash faintly as the oil temp gets to about 60-70c. Oil pressure is 45psi at idle at the same time.  I'm wondering if the temp sender doing this?  
    • Well it runs again!  This was a definite case of while I have it apart lol Everything except the body and interior has been restored, refinished, or replaced.  @socal_stagea is my IG if you're bored and want to see all the pics.
    • I already got plug and play Link ecu G4X. Main concern is that the de loom works on s1 motor or not? I already rewired injector and coils loom to suit my bosch injectors and bosch vag coil. I’m not running any Iacv. For cas running the nz wiring kit i bought the neo plug one so it suits the wiring but don’t know it works or it doesn’t matter they work the same on every motor. For wastegate solenoid do i need to wire straight from ecu? What can i do for iat sensor to work or same run from ecu? For Vct solenoid, right now i got s1 vct solenoid on motor so do i need to remove neo connector and add s1 connector to work? Any other thing i missed i need to do to make the motor working on de loom. Any different mechanism on neo vs s1?
×
×
  • Create New...