Jump to content
SAU Community

Injectr Resistor Pack + Aircon Press sensor

Driver

By Driver,
in Wanted to Buy

 Share

Recommended Posts

GTRgeoff Grand Master

GTRgeoff

Posted
Posted

for the resistor pack you can use 6 10W 10 ohm resistors from Jaycar/Dick Smith. Will cost about $6 but then just package them nicely in a box.

GTRgeoff Grand Master

GTRgeoff

Posted
Posted

Your mom fixes cars????

:) oh sorry, "he"

with the resistors you already have Roy's detail on fitting them? this is the same but just solder the power wire into the 6 resistors at one end (twist them together) then run the other ends to each injector in place of the power wires they have. The switching is done in the ecu to earth the injector and make go bang.......

sluggerS13 Contributor

sluggerS13

Posted
Posted
for the resistor pack you can use 6 10W 10 ohm resistors from Jaycar/Dick Smith. Will cost about $6 but then just package them nicely in a box.

does anyone know the exact ohm and W resistors to use. i've read on these forums so many different things. 8.5 ohms, 7 ohm, 10W, 17W. i don't want to wire the wrong sized ones in and short something out.

  • 4 weeks later...
  • 3 weeks later...
shrike_73 Contributor

shrike_73

Posted
Posted
appaerently, no-one on here knows. so i bought some 6.8ohm resistors. i'll let you know how they go real soon

Hey SluggerS13

Did you end up putting them in and did you take any pics of finished result?

I bought the 10ohm, 10Watt as found another site which a couple of people claimed they used them.

I once found a page which someone posted pics and full instructions of Jarcar resistors installed but have been searching for weeks and can not find it.

Spewing.

thanks.

predator Grand Master

predator

Posted
Posted

There was a page in here, I am sure it was the wanted section in response to somebody looking for the factory item, and it was explained how to make it with fairly clear instructions.. but I can't find it in here anymore either :)

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • OakvilleGTR
      Turn signal wiring question

      By OakvilleGTR · Posted

      Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • sonicii
      Lower A arm Skyline v35

      By sonicii · Posted

      The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
    • Red Sky II
      Looking for autoelectrician in Perth who can do the OEM to double din stereo upgrade.

      By Red Sky II · Posted

      Thanks Paul I reached out to Autotainment but they no longer work on JDM cars as the guy who used to do the work moved on and is no longer doing that kind of work. I am talking with Level Up Audio though.
×
×
  • Create New...