Jump to content
SAU Community

Recommended Posts

Hi peoples,

just got a question relating to any things to check or replace when a car hasnt been running for a few months. Is there anything other than battery/engine oil/filter/fuel filter/water/coolant to check over??

eg the rust on the brake discs, does that just sand off when used again? Brakes? Fuel system/tank?

It was in good order just hasnt even been cranked for a while. rb20det

advice appreciated :(

Link to comment
https://www.sau.com.au/forums/topic/72272-common-problems-car-garaged-for-ages/
Share on other sites

Hi peoples,

just got a question relating to any things to check or replace when a car hasnt been running for a few months. Is there anything other than battery/engine oil/filter/fuel filter/water/coolant to check over??

eg the  rust on the brake discs, does that just sand off when used again? Brakes? Fuel system/tank?

It was in good order just hasnt even been cranked for a while. rb20det

advice appreciated :D

Hi inissane,

how long exactly did you do in jail?

Seems that you've got the main stuff covered inissane.

Don't worry about the rust on the discs, this is only surface stuff, and a gentle/safe drive will have them sorted and looking normal again.

Get your AirCon cranking over too...a must!! (if u have one?)

Someone mentioned fuel??....this will be stale, don't panic, use it!

Once all that petrol is gone, if you really are concerned, change your fuel filter and fill up!!

Are your tyres square yet?

So, how long did you say you were in for?

Anyways, let us know how you go!!!! :wassup:

lol Mark.....pleaded inissane and got off on 3 months!! :wassup: (jokes)

havent needed to drive it daily for a while so its stationary and getting tweaked.....slowly

but yeh changed the fuel filter already so might put the old one on and use a couple of tanks of fuel then put the new one back on I guess...

check tyre pressure...anything else likely to corrode/get stale?

PS- whats the deal with the air con? thanks again

About the most important thing when storing or not using car for long period, is brake fluid. For preference,you should bleed the system right through, so that there is NEW fluid right through the system. Reason ? Brake fluid absorbs moistute, which is why you should renew it every 12 or 18 months anyhow. Moisture lowers the boiling point, and makes brake fade easier. When stored, the moisture can cause rings of corrosion adjacent to seals [especially in wheel slave cylinders] and later cause seal leakage, and occasionally fairly sudden brake failure. This does'nt normally happen when car being used [even with old fluid] as the pistons keep being moved, preventing any corrosion build-up.

lol Mark.....pleaded inissane and got off on 3 months!! :wassup:  (jokes)

havent needed to drive it daily for a while so its stationary and getting tweaked.....slowly

but yeh changed the fuel filter already so might put the old one on and use a couple of tanks of fuel then put the new one back on I guess...

check tyre pressure...anything else likely to corrode/get stale?

PS- whats the deal with the air con?    thanks again

LOL---Glad ur the sort of bloke who can take a joke...that's ace.

OK...Air-con deal......well it's quite simple actually.

Any compressor likes to be used, like all sealed and rotating mechanical devices.

The seals and bearings in these units that make them work the way they do tend to be like girls,........... ignore them and hey get pissed off very quickly.

Switch on the compressor once or twice a week (at least for a few minutes) so the seals stay fresh and the bearings stay lubricated.

What can happen, and I've seen this, is that the compressor gets turned on once in a blue moon and then suddenly seizes, (expensive trick that one, makes a great sound too as it lets go!) Drive belts break, and all sorts of wonderful things happen, simply put.

Do you get the drift?

Anyways, hope this helps a tad.

and..........I hope your bum doesn't hurt too much. :wassup:

About the most important thing when storing or not using car for long period, is brake fluid.  For preference,you should bleed the system right through, so that there is NEW fluid right through the system.  Reason ?  Brake fluid absorbs moistute, which is why you should renew it every 12 or 18 months anyhow.   Moisture lowers the boiling point, and makes brake fade easier. When stored, the moisture can cause rings of corrosion adjacent to seals [especially in wheel slave cylinders] and later cause seal leakage, and occasionally fairly sudden brake failure.  This does'nt normally happen when car being used [even with old fluid] as the pistons keep being moved, preventing any corrosion build-up.

There is actually a word for this.....when a fluid/liquid wants to absorb water.

Is it Hydroscopic?

Good and important thread!!

  • 3 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I’d love to find some where that can recover the dashes to look brand new and original. Mine has a very slight bubble, nothing compared to come I’ve seen though 
    • $170K. I asked one of the guys there as a joke if that price was just for the passenger seat as it was where the price sheet was... he tried really hard to crack a smile 😄 He also mentioned that every single part of the car was inspected and either restored or replaced with a new or as new part, or made from scratch. The interior was incredible, every inch like a new car.
    • Time for a modernisation, throw out the AFM, stock O2s, ECU into the e-waste bin. Rip out the cable throttle, IACV, pedal, etc. into the scrap metal bin. DBW, e-throttle, modern ECU, CANbus wideband, and the thing will drive better than when it left the factory.
    • I agree, don't go trusting those trims. As I said, first step is to put the logger away, and do the basics in diagnosis.   I spend plenty of time with data loggers. I also spend plenty of time teaching "technicians" why they need to stop using their data loggers, and learn real diagnostics.   The amount of data logs I play with would probably blow most people away. I don't just use it to diagnose. I log raw CAN data too, as a nice chunk of my job is reverse engineering what automotive manufacturers are doing.
    • I'm aware, but unless you're actually seeing the voltage the ECU is seeing and you're able to verify the sensors are actually working I find it hard to just trust STFT/LTFT. I will say, logging the ECU comes naturally to me because it's one of the lowest effort methods of diagnosis and I do similar things in my day job all the time. Staring at 20+ charts looking for something that isn't quite right isn't for everyone. NDS1 allows you to log almost everything so that's normally what I do and then sort out the data later. 
×
×
  • Create New...