Jump to content
SAU Community

Recommended Posts

Im wondering if it would be easier for me to import an R33 Skyline GTS-T to America from Australia (queensland) instead of Japan. I am guessing that ya'll have the same emission laws as we do (or a little closer).  What do ya'll think?

If you haven't done so already, better read up on what's involved in getting a Skyline into the US legally - thanks to your laws it isn't at all easy (and at the moment may be impossible). Have a look at the following forums for more info:

Skylines downunder USA forum:

http://forums.skylinesdownunder.co.nz/foru...p?s=&forumid=37

Freshalloy Skylines forum:

http://forums.freshalloy.com/ubbthreads/po...Cat=&Board=UBB4

Link to comment
https://www.sau.com.au/forums/topic/72275-easy-shipping/#findComment-1332292
Share on other sites

Yes i am moving to Australia anyway, but it wont be until Feb 2007. In my hast, i want to bring one state side for a track/race only car. I dont want to have it for the street. Just personal use in autocross and drift events. That way i can gut it and have a sick ass race car. Does anyone know what a R33 GT-R costs in Japan? And is there a switch i could buy for the GT-R to "turn off" the front diff for drifting?

Link to comment
https://www.sau.com.au/forums/topic/72275-easy-shipping/#findComment-1332298
Share on other sites

In answer to your questions, R33 GT-R's start from about 20k AUD, and go up from there depending on condition, year, etc.

You can buy controllers which trick the attessa computer into providing full time awd, full time rwd, or a set split between the two

once again, this gadget is sold on www.nengun.com

Link to comment
https://www.sau.com.au/forums/topic/72275-easy-shipping/#findComment-1333722
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Clinton and I spoke to Alan Heaphy at length last year at the Bathurst 1000 about the Gibson GTR's that he had at the track and the restoration work that his company was involved with. He has a number of people working for him who were part of Gibson Motorsport when these cars were being built and raced. What impressed me the most was the amount of first hand knowledge and information that he and his team have about the Gibson GTR's and their meticulous attention to detail in the restoration and maintenance of these cars.
    • When you track RPM vs time it's clean, unlike the OEM one, even with filtering there are ripples. Means no random misfires or triggering issues at higher RPM, especially if you have big lift cams and a noisier valve train due to heavier springs.
    • Brake Fluid testers are cheap and readily available....eg https://www.supercheapauto.com.au/p/endeavour-brake-fluid-tester-rechargeable/SPO9539349.html
    • Cleaner signal so timing is more accurate at all rpm also found it to start more on first rotation but could also be I've nailed prime and crank fuel. For under $400 and 30mins of your time, its a good solution especially once the optical sensor does start to play up you won't notice it until in higher rpm and it heat soaks.
    • On a 400hp RB, what benefits other than "it's not 30+ years old" are you seeing from the NZ Wiring Kit trigger setup? If it were me going to change triggering, my belief would be to go for a crank trigger to remove the issues caused by what people claim is belt stretch etc, but that's from my understanding a much larger issue for super high power, rather than those in the 400hp and below club.
×
×
  • Create New...