Jump to content
SAU Community

new springs in old coilovers?


Recommended Posts

My suspension has a clunking noise when i turn the steering wheel.

my mechanic says its because the 2 springs in the one coilover (1 short hard spring and a second larger softer spring) have come apart.

He suggested pulling the front coilovers out, taking them to east coast suspension and fitting new springs to the old front coilover assemblies.

is this the best idea?

has anyone else dealt with this differently?

i dont want to go through the expense of replacing the whole coilover.

thanks for the help

Link to comment
Share on other sites

There is an intermediate, (double sided) spring seat that goes between the main spring and the helper/tender spring. Thye soemtikmes slip out or get damaged. Unlikely to be the springs themsleves, my suggestion is to pop into East Coast and they can quickly tell you what is needed.;)

Link to comment
Share on other sites

thanks for the help sydneykid,

i just went to eastcoast,

they told me the bearings at the top were worn and causing the springs to not turn freely,

so im having new camber/castor adjustable tops fitted which come with new bearings,

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Ultimately, if the tip is not far into the runner and the o-ring seals, then you are in business. Have you applied pressure to it as is? It is not really a problem for the injector to twist once it is bolted down, the oring seals it and you don't want it jambed into the oring too hard The plenum is intended to take multiple size lower injectors with different adapters, but the way you have it is fine if they seal.
    • Are these the Dmax ones you are in reference too? https://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35#description Not a bad idea to get the uni flange ones. I have sent just jap an email too. Will see what they say lmao. Only thing is the Dmax ones are on a big back order. Low key anything will be better then my OEM ones I got as they are sounding like popcorn when I go under load lmao 😂☠️🪦.
    • They should do. I have S14 (or something S chassis, anyway) driveshafts in my R32 (because my diff flanges have 3x2). They're the right length. When you go looking for R32/3/4 driveshafts (for turbos), they're all the same thing, so are the same length. So there really shouldn't be any reason why those cheapies from JJ won't also fit an R34. R32/3 NA should also be the same thing. The (3x the price) D-Max ones are uni-fit. They have 5x1 and 3x2 bolt holes and say they cover all the cars. So that would also suggest that they are all the same except for the flanges. And in that case, the flange goes both ways. I'd be buying the D-Max ones if I ever have to replace a shaft. Because that will open up diff options without needing to juggle shafts also. Juggling shafts is gay.
    • Yeah with the adaptors they do look like the photo above - just the fitment within the plenum itself and then further with the rail to the intake is questionable - we shall see tomorrow hopefully once I get some replies from Aeroflow, maybe those bosses are the missing piece....
    • Should be fine, if you have it sitting too far in, you end up just spraying the walls and have shit idle. You "can" run them like that, however I don't think it's a great idea (also depends on your plenum, might be good to just get the injector bosses first, mock it up and see if you need to get the bottom extension) Ideally your injectors, with the extension should look like this  (Not my photos, just Google)
×
×
  • Create New...