Jump to content
SAU Community

A LOT of black smoke.

skyhigh!

By skyhigh!,
in Engines & Forced Induction

 Share

Recommended Posts

skyhigh! Enthusiast

skyhigh!

Posted
Posted

hey all

just replaced my exhaust manifold gasket, put it back together and now the thing wont idle and is producing a crap load of black smoke. the thing is last nite after it was all back together i started it up and it ran fine, but when came to moving it this morn it wont run. i also had a flat battery this morn so when trying to kick it over could it of damaged the ecu in any way?

ive pulled all the pipes off again checking if they were restricted but they were clear. do airflow sensors just pack it in? as this is the only other thing i can think of.

any help would be much appreciated

Link to comment
https://www.sau.com.au/forums/topic/73624-a-lot-of-black-smoke/
Share on other sites
lwells Grand Master

lwells

Posted
Posted

Is it black, or grey? Where is it coming from: exhaust tip or engine bay?

When I replaced the exahust manifold, turbo-to-dump, turbo-to-manfold, and dump-to-front gaskets my R32 GT-R was pumping grey smoke like something was on fire :P After about 30 minutes of idleing, the gaskets finally started to seal and the smoke disappeared.

The idle was a bit high, but was fine otherwise. I had to replace my sparkies the next day as they became fouled, I assume from a combination of (normally) rich running plus screwed A/F ratios due to the exhaust leak, and the 30 minutes it took for things to seal up.

Lucien.

caminperth Grand Master

caminperth

Posted
Posted

Black smoke and not running probably means you didn't connect up a cooler pipe properly when putting everything back together.

AFM sees lots of air so gives the engine lots of fuel. Engine sees little air so pumps the fuel out the back in the form of black smoke and backfires until it floods and stalls.

skyhigh! Enthusiast

skyhigh!

Posted
  • Author
Posted

cheers for all the replies. its all sweet now though. went through and reconnected everything( intercooler pipes, pod assembly) and the thing was still running rough, but after a bout an hour of trying it started, ran rough for bout a min then just kicked in, although it has a bit of a miss now though. time for a full tune me thinks.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R32 update from 1990's spec.

      By Duncan · Posted

      Great to hear you are bringing it out of the shed again. Unless you have specific issues I'd just add the wideband, get a good tune and enjoy it. Certainly no point changing coils etc if they are working. If would add fuel pressure and e85 sensor if you are doing a general update but not if it runs OK and you are just getting it back on track. The other thing is smaller, modern twins, -5 are OK for motorsport but pretty laggy and old tech for street use (of course, if performance is the priority a modern single with twin scroll manifold etc is the go but not cheap). The final thing worth considering is switching to an ethrottle if drivability is still an issue, it should make things a lot simpler and smoother
    • Duncan
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By Duncan · Posted

      Yeah pretty sure they are m4, but best to check, and perhaps use new hardware Also don't over torque them......there was that one time I lost an expensive engine after a workshop overtorqued one of those bolts and it ended up in the oil pump (no, I don't know why they removed the intake mesh either)
    • Komdotkom
      Compressor flow comparison table

      By Komdotkom · Posted

      I might have to shoot them an email. Pity the exchange rate is so bad at the moment. BTW, thanks for posting that table makes interesting reading. 
    • robbo_rb180
      R32 update from 1990's spec.

      By robbo_rb180 · Posted

      Add these Sensors -Wideband, Oil Pressure, Fuel pressure, Intake air temp Good inspection of ignition system of coils, plugs and loom (12v feed and good ground)- a r35 kit is best bang for buck upgrade. A decent tuner should be able to see any issues with the trigger system- a link has good filtering but a good simple upgrade is the nz wiring bolt in kit. Check and replace all the fuel filters- you would be surprised at intank filter after a few years. Also good to check for any leaks on vac hoses and pipe work as has been said. No need to go overboard and spend big $$$ to enjoy the car. A quality tuner is getting harder to find as anyone with a laptop thinks they are a tuner. A link has great features to check sensor voltages and frequency inputs and easy to see live by pressing f12. The link can do a TPS & RPM fuel/ignition mapping on ITB cars then add a 4D table with MAP and ability to add a 5D to it (can help with economy at cruise with wheel speed vs TPS) Where are you located as that will help narrow down a good tuner ?
    • Wazmond
      Stagea Automatic Box

      By Wazmond · Posted

      Reviving an old thread, I reckon my stagea is starting to slip. Car usually gets parked on a hill, narrow driveway so cant go up the driveway smoothly, anyhows, lately first gear feels "sluggish"? Not responsive. Feels like I gotta run the engine more than usual to get off the line...  Any recommendations for transmission servicing in Sydney? Or possibly just an excuse to go manual ?
×
×
  • Create New...