Jump to content
SAU Community

Recommended Posts

Hey guys,

Can't really tell if its always done it and I've just had the stereo on but when I trail of the throttle a little at around 90-100 in 5th I can hear a whine from the tailshaft/diff area.

Can't be sure what it is. Full throttle it goes away, just rolling with no throttle it goes away? Strange, is it possible the gear box is low on oil or something?

They should put dip sticks in gearboxes :D

any help appreciated, cheers!

Link to comment
https://www.sau.com.au/forums/topic/73894-r32-gtst-driveline-whine/
Share on other sites

Yeah that's typical of RB20 gearbox's. Suggest draining the oil and checking for any out-of-the-ordinary metal and if all is OK, filler up with Redline Shockproof Oil and forget about it.

With these box's the noisy parts are the revers idler gear and moreso the input shaft bearing. If you use the Redline Oil and treat em with some respect they can last a VERY long time ( with the noise ).

Hi, thought I would add to this, and perhaps shift perspective.

I have an r32 GTST auto, and have the same issue. I think its not actually to do with the gearbox but rather the diff. It would suprise me if both the manual and auto had the same issue, I think they are made by different manufaturers anyway. Mine is a Jatco 4 speed.

Other reason is, my father in law is a mechanic and he said it was diff noise, so I trust him.

I'm not too worried at the moment as its not too noisy, but, if it gets much worse I might do something about it.

Yes, tell a lie, I believe Rowdy's and mine are the diff. He got his "serviced", which seemed like an expensive fluid change on hindsight, and which did exactly SFA on the noise front.

I rarely hear mine over my exhaust anyway so it doesn't bother me. :rofl:

Change your diff oil , it only takes 2 litres or less. You will want to use Castrol EPX 80-90. Otherwise I would suggest for all of you that you get some Redline Shockproof. It is pretty much the best you can get but is fudgen expensive so I suggest getting in contact with a rep if you can and see if you can buy it through him/her.

Thanks fellas, is diff/gearbox oil changes part of the 100K service? Mine has the timing belt sticker, all new ancillaries belts and a new o2 sensor. Is it safe to assume the gearbox and diff were done too?

How much are we talking for a gearbox and diff oil change. I can't really say I feel like changing them myself.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It's aftermarket. It also reeks of Honda Civic tryhard from 2003. But if you want one....then you want one.
    • Well some mostly good news and some slight bad news.  Good news is cylinder 6 did in fact only require a honing and I'm good to run my 86.5mm pistons again. I should also get the block back by end of week. Bad news, had a few surprises pop up. First, main and rod bearings were trashed. No sign of any heat damage. I knew right away what caused this... I had not packed my oil pump originally and spent a lot more time than I would have liked cranking the motor to get oil pressure. It sounded fine once started so I chucked it up to luck and forgot about it. Luckily rod and crank are fine and just need new bearings. Engine builder agreed that this was the cause.    Another surprise that carbon covered up very well that I didn't catch, something got sucked up and went through cylinder 1, 2 and 3. Luckily this was no cause for concern, just needed a bit of cleaning up. Valves look fine but he will vacuum test the head this week to confirm. I'm presuming this was something left over from welding my intercooler piping, but we'll never know. I'm going to thoroughly reclean everything.    So all in all, happy the motor is fine, and I'll get it back much sooner than expected. I'll also be taking the time to convert my WMI system over to direct port. I'll snap some pictures of that when the parts come in. 
    • I understand, thanks. Yeah I wouldn't want the car to tip over, I'll try and use the sills, I don't want to risk smashing the chassis rails. I ordered some rubber pucks that have a hopefully big enough slotting. If the front right gives me trouble I can always just make a wood block. I'll measure and inspect the sills closer once I actually take the car up. I hope so, but the rubber blocks I had in hand so far were pretty damn firm, if they are that hard they won't give much way. I'll let you know what happens. Angle grinding rubber isn't one of my favorite tasks. I'll probably start a build thread soon, for my own documentation and "log" as well as sharing what's going on with the car.
    • Kinda something I have been thinking about.  To be honest, we bought it already driving like that.  So there's no telling how long it actually has been driving like this.  Hopefully damage is too bad when we drop the pan.   I am having a hard time finding a site that sells the solenoid for the 5 speed auto, do you have any suggestions?
    • That'll be most likely down the road...  LOL  
×
×
  • Create New...