Jump to content
SAU Community

Recommended Posts

Ok here's the story...

Car is completely stock, no power mods, only suspension bits.

January - Installed a pod filter, only a crappy cardboard (template) heatshield.

- Ran on the dyno, made 108.4rwkw (at night).

Got off my arse, and decided to make a proper heatshield and decided to throw in the stock airbox snorkel to see if it made a difference. See here

On the street the car seems to accelerate a little more smoothly.

I was keen to see what difference the snorkel had done.

May - Proper heatshield and snorkel installed.

- Ran on the same dyno, made 108.0rwkw (at midday).

Here are the two dyno-charts.

Ok the 2nd run made 0.4 less kw - and I took into account that it was due to

ambient temperature. Either way 0.4 is not very much, and indicates that the dyno is reading correctly.

But what's more important are the AFR's, just by installing a snorkel + heatshield, I have smoothed out the air and fuel mixtures.

This may be something to consider, to those who have pod filters and those who think they may need a SAFC to fix their ratio's.

Image1.jpg

Image2.jpg

Hope this helps. :rofl:

Eugene

Link to comment
https://www.sau.com.au/forums/topic/74355-an-interesting-find/
Share on other sites

paully_tee: would it be possibleto post up pictures of this custom intake?

I am just saying that alot of people tend to take off the snorkel when installing a pod filter,

and proven that it is in fact a reasonable idea to throw it back in if you dont want a custom intake made up.

Also taking out the passenger headlight for a run down the strip may prove beneficial.

Eugene

check out mine:

http://www.filejunkies.net/sighost/images/airbox1.jpg

http://www.filejunkies.net/sighost/images/airbox2.jpg

i am planning to get a 100mm hole saw and make a hole direcly below where the pod sits and run a bit of 100mm duct from just behind frontbar :D

I have done this but haven;t run a pipe (ie there is just a hole for the pod to suck through). didn't notice much difference.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, I've been a little busy on this car. I replaced the bonnet struts which is always satisfying but very confusing that nobody else on the planet seems to do this. Its just my routine first thing I do on any car I buy. The boot struts for both the tailgate and the separately opening glass window was a bastard. And, I found a fair bit of rust in the strut cavity. I filled it with rust converter and cleaned up as much of the dirt as I could. There was so much dirt. One piece of the trim was barely hanging on and so I've left it off. I'll try to get a replacement. You can see how disgusting and dirty it all was in this thread; I had to remove the little clips that hold the struts on the ball. The ones I took off had no clips and it was impossible to get them on with them in place. Fingers crossed they stay put. So, I turned my attention to the headlights, they were in a bad way and likely would stop rego. I took the headlights out and found the adjusters were all just loose. So, I fixed those and unclipped the lenses to clean them up. Couldn't believe how easy it was to take all this apart compared to the E90.   I also cleaned up the stockies which was awesome, these are super cool with lug nut covers. They're in good nic but the tyres are shot. I was going to use these for rego but in the end got a fresh pair of rubber for the 17's on the front of the car instead. The front bar of this car is from a late(r) model one. I don't think it's quite LCI but who knows. I'll need to find out. Anyway, the bar was missing the fog lights and the wiring and plugs were for the original ones so I got new plugs and some cheap fogs. I wasn't sure if missing original equipment would hamper my blue slip attempts. Had a couple of these little fellas helping out. But not Ben who got stuck behind the pool heater .... How embarressment.  I ordered new speed sensors for all corners because I knew one was out. I just got cheapies and will replace them with Bosch items when I can find Bosch items. Again, this was just for rego. Alas, it seems the blue speed sensors are not the same as the grey ones. Back they went and replacements ordered. In the end, with my new scan tool, it was just rear left that was shot. Replaced it and cleared the codes. All good now. Lastly, my aux (thermo) fan is being a bit odd. Its powering up at strange times and NOT powering up when I think it should (100C). While this can be caused by a few things, the most likely (for me) is the ambient temp sensor. Given mine reads -40.0C regardless of the temp, I figured it would be good to replace it. In the end, the sensor wiring was abysmal with (terrible) attempts made by somebody to fix it.   I fixed this all up but the sensor is only attached using pins into the wires. The plug is not there. Despite trying and trying to connect it securely it wouldn't work so a replacement sensor and plug is on the way. Oh, I also ordered a replacement piece of trim for the part missing here at the bottom. Ordered from Latvia for $70 delivered. I took a bit of a leap of faith because I didn't have the exact part number and, as usual, there were eleventy billion pieces of trim that looked to fit. Nailed it. Well, its not totally perfect but I think its more a 28 y/o car problem than a trim problem. And, as of today ..... I have bought the workshop manuals 2nd hand off a guy in tassie. 1000+ pages of E39 goodness, hopefully it helps me with the fan. I also have a new temp switch on the way incase its the problem. Stoked.
    • I don't even know that you want an M2 Competition as a track car. My rule for a track car is only risk as much as you're willing to completely total out. Clean stock C5 Z06 Corvettes out here are cheap. Buying someone else's already ruined track car is even cheaper. Maybe I'm just not that good a driver but even a Fiesta ST on the Nordschleife felt like as much car as I could realistically handle.
    • I've already gone over the cam. A new one is going in. An old one is coming out! The new one is smaller, with less overlap. It has way more lift, but it will be more mild mannered (hopefully, probably very minorly) I'm also measuring for two more mufflers, with the goal of having four mufflers in my car. But that probably will be done by an exhaust shop in a drive in, measure, buy parts, install parts later kind of deal.
    • Mine is not even a GTR and I've been resisting the urge to make it a power monster for the last 25 years. And as a consequence, I have driven it to work nearly every day across that span of time.
    • Since the motor is out, I suggest pop in a nice dirty LS chop cam. MOAR of this please:  
×
×
  • Create New...