Jump to content
SAU Community

Recommended Posts

Hey guys,

Yesterday my car wouldn't turn over, my first suspect was a flat battery, so we tryed to jump it... comming to conclusions that the leads were had it, we roll started my car, and off she went.

Once i get home, i charge the battery, and it still doesnt turn over (makes a 'tick' noise and nothing more.

I then began to take the starter motor out, and after not be able to find one today, i decide that i'll have a crack at it, pull it apart, was a bit stiff so i sprayed some wd40 in it loosened it up, then took it to my mechanic who then tested it. According to my mechanic, the starter motor is fine, and it should start the car, he told me to check my electricals.. After this, i put the starter motor back in, and turned it over, still the same result as before!

Im now really confused as to what to do next? I got the volt metre out and put it on the power to the starter motor, and it showed 11.0 volts when the car was on ignition, but then when i turn the key it goes down to 0.0 volts straight away.

Does anyone have any ideas as to what to check?? Please help, im really stumped and need my car back asap.

Thanks so much in advance.

Dayne

Link to comment
https://www.sau.com.au/forums/topic/75003-my-skyline-wont-start/
Share on other sites

I have tried a jump pack with a battery inside it thats good to start semi-trailors..

i have tried my parents ss commodore to jump it with new leads, i have tried a civic vti-r, i've tried a ford ute.. so thats 3 different cars.. and the battery is brand new ( 2 weeks old) and reads a voltage of 13.5 (has been on the charger for over 24hours now) so it is definetly not the battery..

Is the key actually turning the whole way round, or does it turn most of the way then, resist? It could be the actual ignition switch. My car wouldn't start normally, only when pushed. Opened the case underneath the steering wheel, ignition barrel and switch, found that it was cracked. Replaced the ignition switch (easy, just a screw and a few plugs) and solved the problem.

Check the voltage at the battery when cranking. If the voltage drops to zero then you have a problem with the ignition. Check under the dash for any melted wires behind the ignition barrel. If the battery is brand new then remove it and try to start one of the above mentioned cars with it. This will rule out the battery. I have seen brand new batteries shit themselves. Have you tried doing a half turn on the ignition?

If not, put the key into the ON position, then slowly turn the key towards START. Don't turn it all the way, just very slowly to see if maybe the barrel is passing the circuit. It is also possible that you starter motor is drawing too much current but I doubt it will drop all the way to 0.0 straight away.

Alright,

My dad helped me look at it, after cleaning the starter motor up, it seemed to be working fine.

Charged the battery, then it still didnt start.

We re-attached the terminals and re cleaned them then jumped it off my parents 5.7L SS with heavy duty leads with the ecu protector, started first go after turning it and leaving it there for a bit..

Now the car sits at 14volts the whole time!:(

Thanks so much guys.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The jack pad placement always had me scratching my head. I only have a small section to work with on both the E90 and E70 (and insert new project car here ) and I could see lining it up to be a bit of a bugger. For me, the E90 is just too low and needs small ramps and then the front centre jack point is a bit tricky to line up (it's half way down the subframe and about the size of a tennis ball, its really hard to see unless your head is on the ground), so I definitely like the idea of not having to do a multi-stage jack and just sliding these bad boys in under the sides. There's only one small point at each corner, so I can't jack AND add a stand on the same corner. Or, maybe I can and I'm too nervous to try. 😟
    • Is this not the biggest deal of all? I was hoping the whole "will slide under cars with skirts etc and lift evenly quickly with minimal fuss" was the entire point of such a device? 
    • Here's Neil's car up on mine recently
    • Yeah I've got one of these, Quick Jack not Quick Lift, but your link looks like a good copy For me, it's better than no hoist, but it is definitely not as good as a hoist  It lifts the car about 60cm which is a nice working height compared to regular stands and it is only under the sills so it doesn't get in the way like regular chassis stands do.  No need to use regular stands, it has a safety lock on it. On the down side it is really heavy/unwieldy to drag into place, and you have to place it after the car is there (no option to drive the car to where the frames are. You need to try and line it up with the proper sill points which is hard as it swings up in an arc and there is surprisingly little adjustment in the distance between the rubber pads for different car lengths. Not a big deal, but in practice a jack + stands is probably quicker. Also there are hydraulic lines to each side and you need either a 240v or 12v source to power it depending on which option you have, I use 12v as I always seem to have a battery around.
    • Finally addressing my catch can and oil setup Plan is to do as much as practical without having to remove the motor or pull it apart. (no back of head to sump drain/breather or oil restrictors) First step is a set of full length baffle plates from Hypertune and a Tomei cam cap stud kit. I could probably have laser cut and bent up my own ones but this took any guess work out
×
×
  • Create New...