Jump to content
SAU Community

Recommended Posts

Updated price: $7,500

Updated with pictures

Has 102,000km on the clock

Is a stock standard RB25DET and gearbox and clutch and driveline

Interior drivers garnish and air con vents are damaged, have a new one here

Diff provides no drive, I assume the drivers side halfshaft has been pulled out of the diff.

Needs a rear quarter cut, drivers side suspension subframe and drivers door. A-pillar is unharmed. B-pillar needs a little straightening where the drivers side intrusion bar bent it backwards about a centimetre.

Bootlid is fine but now needs a little touchup paint on the edge because the rear quarter is touching the bootlid and the hinge of the bootlid is pushed about 1cm in, therefore the boot doesn't shut properly.

From a couple of us checking the car out, we *dont think* the subframe is bent but still could be by an unnoticeably small amount.

Needs a new wheel and rear caliper assembly, they were broken as part of the accident.

The engine and gearbox stock standard and are perfect, the owner was a big wuss when it came to thrashing cars.

Car has no rego, registration has been cancelled. There are no debts on it either. It is fully complied under low volume system, been in Australia for a few years with the one owner.

Click each picture for a large version

01.JPG

02.JPG

03.JPG

04.JPG

05.JPG

06.JPG

07.JPG

08.JPG

09.JPG

10.JPG

11.JPG

12.JPG

13.JPG

14.JPG

15.JPG

Sorry, only going from memory. Will get more details in the next few days

Approx 100,000km

5 speed manual (as per thread title)

I think its a 1993 model

No mods

Fully owned and complied (green plates), no rego.

Interior in very good condition

Comes with some spare parts

Bootlid is OK, rear bumper and RHS taillight needs replacing

Front bumper needs a respray

Otherwise the car is in very good condition

  • 1 month later...

Nar not drift damage. Sitting on Middleborough Rd waiting to turn right and an unlicenced driver with no fixed address driving someone elses unregistered car slammed into the skyline :P

Hey mate,

Have you looked to see what a 1993 GTS-T goes for? And in repairs and damage there is easy $4000-5000 so why would someone go through all that to save $3000 and know they bought a damaged car. I will offer you $2000 cash as long as you are willing to provide all vehicle details for a Revs Check

G

Hey mate, you are VERY funny.

This car may also be used for wrecking. Have you priced up a halfcut lately? How much do you think an rb25det engine alone goes for?

$2000 hahahaha.

Do you really have nothing better to do than post rubbish in other peoples threads? If you're not going to buy it then get lost, I nor anybody else is interested in hearing your drivel.

  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • As you're looking at using a Link ECU, then large injectors are not a problem. But there's not really any need to go 1000s on an RB20 unless you're planning >>600HP on E85, which would seem unlikely. There are other options for injectors. The Xspurt ones are available from a number of places and you can get them in the mid 600s and 725cc, which is probably a sensible place to be. These are all EV14 based. If you are not using the stock AFM (at all, which would be the case with a Link) then a large turbo intake pipe to suit the ATR turbos is not an obstacle, so you should use one instead of a highflow. Results will be better.
    • Hey guys,  I'm after some advice and this here is the best place to get it imo. I was a member a looong time ago under another account, with a lost email address. Its nice to jump back on and see some of the same names still giving good advice.  I mothballed my car when i moved to perth in 2013, and after getting towed across the nullabor a few times it has officially done more km's on a trailer than under its own power. Now that i have started the process of tidying up and modifying it, i see the fruit available (and the fruiterers selling the produce) is different than back in the day. hence my questions, as i used to 'know' what to get and now, i'm not so sure. Engine wise the car (92 gtst) has a walbro 255, k+n, fmic, cam gears and and turbo back 3"exhaust. Wish list is a Hypergear high flow or ATR43G1, Link G4x and some newer injectors before a tune up. My goals are modest, only low 200's power wise. i know i could achieve this with less, but i've been swapping out old for new where i can. Every cooling hose has been replaced, along with mani gaskets, WP, thermostat and radiator, fuel pump and timing belt, tensioner and idler, and i rebuilt the steering rack. Regarding the injectors, the fruiterers all seem to sell what used to be considered quite large injectors. There are a lot of options for bosch 1000cc EV14's, and i would like to know if that is a suitable choice for my build. Is modern injector design good enough to run these at the low duty cycles that i likely would be? is there a downside to running a too large injector these days? or, would there be an upside to running a smaller injector at higher duty cycle? I can see that there are smaller injectors still available, but the ones i have seen specifically marketed for RB's are pretty large (see: https://golebysparts.au/collections/fuel-rail-injector-kits/products/nissan-rb20-fuel-rail-bosch-980cc-1150cc-injectors-turbosmart-fpr800-regulator-kit), and i dont know enough about them to say one not marketed for RB's would fit or not. I have searched the forums, and amongst all the posts on older tech, I did see gtsboy recommend EV14's, but no size was mentioned... again, i'm not clear on if the smaller size bosch injectors are also EV14's as they do look similar.  also, if someone can recommend a tuner familiar with RB's in the Geelong or West Melbourne area i'd appreciate it. Thanks in advance guys. Cheers, Rowdy  
    • FWIW the depth of the groove in the rubber pad is not super essential, the blocks are rubber and squish a bit. If you are worried an angle grinder will make a deeper groove quick smart
    • I mean, if you were to move the jacking points away from the original location, that is, away from the wheels and closer to the centreline of the car, then it will be more likely to overbalance and tip off the supports. Same as we talked about before. I was talking about moving for-aft. If the sill is bent outward or inward, then the car would obviously look unstraight from the outside. Hopefully that hasn't happened either. Again, you can do comparative measurements from the chassis rails to see if there is much deflection.
    • Can you elaborate what you mean with your first sentence? I meant move as in the bulge kinda seemed like it got pulled "outward" meaning it got pulled down and to the side with the jacking rail itself, so the load bearing bulge now sits lower than usual and is not level with the sill on the other side of the jack point. Either that or the jacking rail just got pushed in a good bit.
×
×
  • Create New...