Jump to content
SAU Community

Recommended Posts

afaik

Factory specs are 135-185 psi per cylinder and each cylinder being around 120 with an ~<5psi variance is decent for a >100,000km car.

Just means your car isn't in top condition, someone's had fun in it :D but it should be alright for a while (That's assuming my factory spec figures are correct)

i got mine checked it come out with all in the 120's but there all around them same  

broke that checked it said it was all good but that seems low to me is it ok

ingnore the other comments, outirght compression figures are not very relevant, as things such as how warm the engine is and battery voltage affect the outright figure.

what is important is that all figures are even, as it is unlikely that all cylinders have the same damage (if any).

usually a bad result would be say 5 cylinders having similar compression (within 3 or 4psi) and one cylinder (usually cylinder 6) having compression which is 25psi different.

as long as the figures are within about 3% from max to minimum its fine. so basically from what u explained the motor should be fine. if u really want to be sure do a leakdown test but that is usually only done if compression test turns out bad.

Knore's comment is sort of correct as most cars show compression around 155psi

they all got ok they got

1 124

2 125

3 125

4 123

5 124

6 125

is there a way to higher then compression

also i hear low compress means more lag

the tune is ****ed on the car so they r retuning the link computer the day i buy it they said thats y it is laggy and shit

they all got ok they got  

1  124

2 125

3 125

4 123

5 124

6 125

is there a way to higher then compression  

also i hear low compress means more lag  

the tune is ****ed on the car so they r retuning the link computer the day i buy it they said thats y it is laggy and shit

those compression figures are fine.

also the compression u are reffering to when u say it means more lag is something u cannot change. what u are reffering to is the compression ratio, ie. the relationship between the volume of air in the cylinder when the piston is at the bottom of its stroke compared to when its at the top.

u can make it less laggy with good tuning, although with a stock turbo it shouldnt be laggy either way.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...