Jump to content
SAU Community

Recommended Posts

Well not actually the engine itself.

Last night I went to adjust the boost a little on my little boost controller (the one mark sells on here) and split the hose.

Thought no worries. Replaced the hose but when I took the car for a drive it made a weird "whurling" type noise with any ammount of boost pressure. To me sorta sounds like a air leak but not sure< is that what noise it would make if a cooler hose blew off?

Even with the hose removed it still makes the same noise.

I thought I might have tore a little hole in one of the pipes from the afm to the turbos but they all seem ok, removed the clamps etc and checked under there.

Anyone know what it could be?

Link to comment
https://www.sau.com.au/forums/topic/75736-rb26-making-weird-noise/
Share on other sites

argghhh. hope its not one of the gaskets.

car still runs fine, it will make boost but seems to be down a little bit on power. the noise also seems to go away after around 3000rpm, sort of when the turbos really start spooling.

most likely one of the turbo gaskets? would it be a head gasket? what are the symptoms of that?

it sounds like a ghost comin from my engine bay. can really only hear it from 2000-3000 revs under load, even coming off load from about 5000revs you cant hear it again till it comes down to 3000 or so again.

Im guessing its one of the turbo gaskets? maybe to the manifold. Surly someone knows what it is. Car still drives fine and comes on boost fine.

it sounds like a ghost comin from my engine bay. can really only hear it from 2000-3000 revs under load, even coming off load from about 5000revs you cant hear it again till it comes down to 3000 or so again.

Im guessing its one of the turbo gaskets? maybe to the manifold. Surly someone knows what it is. Car still drives fine and comes on boost fine.

Ive had something very similar in my R32, ended up being a gasket just off the turbo..

Gaskets.JPG

Ive had something very similar in my R32, ended up being a gasket just off the turbo..

Its quite common for the bolts on the "Twin Turbo" pipe to work loose, particularly for the rear turbo, and the gasket to blow. Unfortunately they are not a standard gasket so you have to get them from Nissan AFAIK (or as I did, make them).

I currently have a high-pitched leak somewhere (plus backfiring) and I am pretty sure its the same gasket. :(

Lucien.

thanks champs, ill swap them next week and see how it goes. I hope its just one of them so the turbos dont have to come out.

Can I buy just those 4 gaskets or do I have to buy the whole set from nissan?

also will the leak cause any damage or is it still ok to go boosting it a little for normal driving?

Its three gaskets, and Nissan doesn't do turbo gasket sets anymore, so you just order in the three.

Before you do though, better to check that's what is actually causing the problem. The recommendation I have seen lately is to mix up some detergent with water and put it in a spray bottle. Spray all the possible connections, fiddle with the throttle to rev it a bit, and look for the bubbles.

Hard to say if it will cause any damage without knowing exactly what/where it is. At a guess, probably not, but it will throw the mixtures out as air is escaping.

LW.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I think my main complaint with your idea is that there is a veneer of idealism spread across it. You want the simple numbers to make it easier, but all they will do is make it easier for someone to come to the wrong conclusion because the fine details will kick them in the nuts. As it is right now, the tiny bit of arithmetic is NOT the obstacle to understanding what will fit and what will not fit. The reality of trying it is what determines whether it will fit. If you had a "standard rule" that R34 GTT guards have that magic 100mm space from the hub face to whichever side you were worried about, and someone said "excellent, this wheel is only 98mm in that direction, I'll just go spend $4k on them and jam them on my sick ride".....they would just as likely find out that the "standard rule" is not true because the rear subframe is offset to one side by a fairly typical (but variable) 8mm on their car and they only have 92mm on one side and 108 on the other.
    • It still combines inches with mm, especially when you have .5 inches involved, and mm and inches that can go in either direction. This would give a clear idea on both sides of the rim, right away, with no arithmetic. Even better if somebody gives you the dimensions of the arch of multiple cars. i.e GTR may be 125mm, a A80 Supra may be 117mm, or something along those lines. Yes, you can 'know' that going from a 10in rim to a 10.5in rim with the same offset moves both sides about 6mm, but you still have to 'know' that and do the math. Often it's combined. People are going from 9.5 +27 to 10.5 +15. You may do the math to know it, but if it was going from (I had to go look it up to be sure) 241mm/2 - 27 - 93.5mm from the center line to (more math) 266/2 - 15 (118mm) from the center line. Versus 93mm vs 118mm. It's right there. If you know you have a GTT with 100mm guards you can see right away that one is close to flush and the other absolutely won't work. And when someone says "Oh the GTR is 120mm" suddenly you see that the 10.5 +15 is about perfect. (or you go and buy rims with approximately 118mm outward guard space) I think it's safe to say that given one of the most common questions in all modified cars is "How do offsets work" and "How do I know if wheels will fit on my car" that this would be much simpler... Of course, nothing will really change and nobody is going to remanufacture wheels and ditch inches and offset based on this conversation :p We'll all go "18x9+30 will line up pretty close to the guards for a R34 GTT (84mm)" but 'pretty close' is still not really defined (it is now!) and if you really care you still have go measure. Yes it depends on camber and height and dynamic movement, but so do all wheels no matter what you measure it for.
    • But offsets are simple numbers. 8" wheel? Call it 200mm, near enough. +35 offset? OK, so that means the hub face is that far out from the wheel centreline. Which is 2s of mental arithmetic to get to 65mm to outer edge and 135mm to inner. It's hardly any more effort for any other wheel width or offset. As I said, I just close my eyes and can see a picture of the wheel when given the width and offset. That wouldn't help me trust that a marginal fitment would actually go in and clear everything, any more than the supposedly simple numbers you're talking about. I dunno. Maybe I just automatically do numbers.
    • Sure! But you at least have simple numbers instead of 8.5 inches +/mm, relative to your current rims you do maths with as well, and/or compare with OEM diameter, which you also need to know/research/confirm..
×
×
  • Create New...