Jump to content
SAU Community

Recommended Posts

Hi everyone

I got my new car yesterday and i noticed a couple of times when idling it will just start adling up and down without anything being touched after a while and sometimes it will sit at around 800rpm steadily and then sometimes around 5/600. Is something wrong? or do they just have dodgy idle sensors or something cause my last 1996 series 2 gts-t didnt do it but this is a 1995 gts-t

Link to comment
https://www.sau.com.au/forums/topic/75777-upand-down-idling-s/
Share on other sites

Usually, a problem in the TPS is a constant high (around 1500 - 2000 rpm) idle. Usually caused by the sensor getting out of alignment and not sending the "throttle closed" signal to the ECU.

Variable idle is usually caused by a dirty / sticking AAC valve. That's the little cylinder on the back of the plenum chamber. It can be removed, disassembled and cleaned out with a bit of Car-B-Clean, then re-assembled and re-fitted without too much drama.

could be a vacume leak,

blind elk, thats true however my tps was out of wack in the other direction, what would happen, is it would idle fine, but you woul pull up to a stop sign, dip the clutch and the idle would **** around for a few seconds, worth checking, also the

and low speed driving was a bitch, car runs like crap, i dont think it will see 100% throttle either when you nail it

if your going to adjust idle , disconnect the brown plug on the solinoid behind it when your finished, reconnect it

Just had my 33 serviced not even a month ago, and after 3 mnths of pretty crappy idling, apparently a vacuum leak near idle starter motor was fixed, afm cleaned, tps adjusted, and timing reset.

Just last week it started ranging again from like 200-1200 rpm up and down as if i was stepping on and off the accelerator...

I have a non-oil blitz pod filter, and a blitz 3inch exhaust.

Any ideas on what else could be causing it in my particular case would be appreciated.

Cheers

-Serge

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...