Jump to content
SAU Community

Recommended Posts

I'm 16 and have always been a skyline enthusiast.

i had been telling my dad that the skyline is the car for me, but he did not approve because they come stock turbo. :werd:

Recently my dad's freind knew of this guy that imports cars from japan to Australia and recently brought one in.

For a price of 14,000 my dad and i went to check it out.

when we got there we popd the hood then had a look at the registration.

it said " Nissan Skyline r33.:"

it is not turbo and i cannot find if its a gts, or whatever. all it has is a gt at the sides and an "s" at the front.

its a twin cam 24 valve non turbo skyline.

to me, ive never heard of just a Nissan skyline r33.

its a 1995 model.

ive never heard of just a nissan skyline r33 gt

please give your thourghts on what it is? :confused:

it may not have turbo but i blown away by the amount of take of acceleration it has.

cheers

FLYR33

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/
Share on other sites

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

check the blue plate in the back left hand corner. a non turbo will say where the engine is RB25DE. a turbo will say RB25DET. Thats how you can tell, if not check the in side dash, if it has a built in boost guage where the rpm tacho is.

these are just some ways that you can tell

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/#findComment-1409820
Share on other sites

Take care it isn't a GTS, those have the SOHC 2.0L engine - will have for the engine designation RB20E on the firewall plate if it is. They are 'somewhat' underpowered....

Most likely it is a GTS25, as mentioned that will have RB25DE on the firewall plate. 200HP from the NA 2.5 means they are fairly quick.....

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/#findComment-1409917
Share on other sites

ok the plate is on the firewall most usually on the left side.

the firewall is at the back of the engine, the wall that seperates the engine from the cabin.

NA means Naturally Aspirated, which means non-turbo.

Hope that clears up some confusion

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/#findComment-1411440
Share on other sites

I've got a Rb20E mate and theyre not that bad, good car to learn on, still pisses on lancers and shit like that, so i wouldnt worry too much if thats what it is, rb25's are good motors, and by the sounds of the 24valve it sounds like one!

Goodluck, and lets hope its a good car!

It should also say on the compliance plate which is a green plate mines on top of the strut tower, and it'll say what make it is and who its complianced by and the date!

Dayne

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/#findComment-1411549
Share on other sites

ok the plate is on the firewall most usually on the left side.

the firewall is at the back of the engine, the wall that seperates the engine from the cabin.

That's left hand side as you look from the front of the car toward the back of the engine bay. Just to the left of the brake master cylinder.

24 valve - yup, that would indicate a RB25DE (GTS25) as I think the RB20E (GTS) is 12 valve due to the SOHC head?

Dayne - yup, GTS's are still better than a lot of cars out there! Just be sure that you don't pay a premium for one. In NZ the GTSs are significantly cheaper (and thus far more common) than the GTS25s.

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/#findComment-1414094
Share on other sites

ok the plate is on the firewall most usually on the left side.

the firewall is at the back of the engine, the wall that seperates the engine from the cabin.

NA means Naturally Aspirated, which means non-turbo.

Hope that clears up some confusion

THANKS MATE

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/#findComment-1414363
Share on other sites

The GT badge on the side of the car has nothing to do with the cars motor. It is just the famous GT badge associated with Skylines.

In the R33 range as said earlier:

GTS = 2lt Non turbo.

GTS25 = 2.5lt Non turbo

GTS25T = 2.5lt Single turbo

GTS4 = 2.5lt Single turbo or NA + 4wd

GTR = 2.6lt Twin Turbo 4wd

All very good cars. Not a fan of non turbo Skylines though as I think it defeats the point.

I know that coment will cause some tension. i might just run and hide under my turbo...

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/#findComment-1416015
Share on other sites

Dayne - yup, GTS's are still better than a lot of cars out there! Just be sure that you don't pay a premium for one. In NZ the GTSs are significantly cheaper (and thus far more common) than the GTS25s.

Got mine at a good price anyways:) considering upgrading to RB20det in it this holidays though.. or 25DE

Dayne

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/#findComment-1416155
Share on other sites

The GT badge on the side of the car has nothing to do with the cars motor. It is just the famous GT badge associated with Skylines.

In the R33 range as said earlier:

GTS = 2lt Non turbo.  

GTS25 = 2.5lt Non turbo

GTS25T = 2.5lt Single turbo

GTS4 = 2.5lt Single turbo or NA + 4wd

GTR = 2.6lt Twin Turbo 4wd

All very good cars. Not a fan of non turbo Skylines though as I think it defeats the point.  

I know that coment will cause some tension. i might just run and hide under my turbo...

thats like saying getting a standard commodore without a supercharger defeats the point.

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/#findComment-1416173
Share on other sites

GTS4 = 2.5lt Single turbo or NA + 4wd

I have never heard of an R33 GTS4 Turbo, all the 33 GTS4's I've seen have been NA

The only other single turbo GTS4 I've seen is an R32 GTS4.

and before someone makes a smart arsed comment, GTR's with single turbo conversions dont count :(;)

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/#findComment-1417072
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...