Jump to content
SAU Community

Recommended Posts

  • Replies 345
  • Created
  • Last Reply

Top Posters In This Topic

Buddy Club P1 QF FORGED with comp rubber 7.4kg rim weight

18x10 +12 all round.

114.3 5 hole

Falken Azenis semi comp 245/40/18

GT-R suitable.

one slight scratch on one rim. No gutter damage whatsoever.

$3000 landed. ( coming soon )

kaireican-img600x450-1123988210dsc05354.jpg

sure thing Rick.

we so require a 50% securing deposit prior to bidding/purchasing.

Once we have secured the product, shipping takes approximately 6 weeks to reach your door. Once they have landed here in sydney, we request final payment prior to sending the product to you via local courier.

HOLY CRAP!

I was under the impression it was the whole asking price then we receive the goods?

HOLY CRAP!

I was under the impression it was the whole asking price then we receive the goods?

50% up front.

50% once goods land in Australia.

Goods not released until payment is made in full.

i think that makes it clear. :)

  • 2 weeks later...
NISMO LM GT3

18x10 +20 all round GT-R suitable.

two rims have very slight gutter mark.

Dunlop FM-901 rubber 275/35/18

Closing August 29th. This set will sell and won't be relisted.

$2700 landed

tera374638-img600x450-1122201523dscf0459.jpg

tera374638-img600x450-1122201562dscf0461.jpg

They relisted - 128,000 "buy it now" ! Tempting but does that rubber look fairly worn out to you? Can't tell, bad angles. What does the text say about it?

  • 2 weeks later...

TBee,

these are more suited to the R33 and R34.

however, being a 9.5" rim, the +12 offset will certainly bring the wheels out to the edge of the guards, perhaps lipping of the guards will be enough. will double check.

ok, just checked... these were originally on a R34.

i know 10" rims can fit under a R32 with a +22 to +25 offset.

given those specs, these rims are a 9.5" width, taking into consideration that the offsets are bringing the wheels out a further 10-12mm with only 6mm less rim on the outer, these wheels will be sitting approximately 6mm further out than a 10" with a +22ish offset.

slight rolling of the guards may be needed to get these babies to fit.

estimating between $2500 and $2800 landed at this stage.

How much do you think those GramLights 57C will go for ?

I'd be only really after something with almost brand new rubber?

Cheers

That set in particular closed nine days ago, as mentioned on the post.

( September 7th )

I can source out some other rims that may be of interest.

Do you have sizes in mind?

17 inch 9/9.5 wide? rubber included i pressume.

Cheers.

Volk Racing GT-C in BLACK

18x9 +18 all round.

GT-R suitable.

Bids close September 23rd.

moro3_2000-img600x450-1126833718img_1001.jpg

Work Meister S1

18x9.5 +20 all round. some minor gutter scuffs.

Yoko rubber. 265/35/18

6-7mm tread

Closing September 23rd

from $3600 landed

miyupapa11-img600x450-1126859273aomori_108.jpg




  • Similar Content

  • Latest Posts

    • So, the other thing I've sorted is a baseline dyno run up at Unigroup's new location. The auto trans was a little unco-operative by both shifting down when the throttle was floored on the dyno (so Mark had to ramp it up more slowly than in a manual) and also by shifting up at 6,000 even in sports mode instead of the indicated redline of 7,000 Still, on a hot day it made 240rwkw at 16psi which seems about right for 300kw (400hp) through an auto at the wheels.  The shape of the curve is not quite right because it was not full throttle to about 4,500 to stop it kicking down, but until I can get a tune on the auto trans control this was the best we could do.....full boost will be well below 5,000 once that is sorted, I'll get some data logs when I can to confirm For comparison, the R32 made 255 at 12psi (at 4,500) on the same dyno with tune, n1 turbos, cam gears, big exhaust but otherwise all standard so the v37 is likely a little better out of the box. One thing that is very clear is that the standard water to air intercoolers are not up to sustained use at full throttle in warm ambient temps. After about 5 runs (so only a few minutes full throttle), it was pulling boost and timing and dropping 10-15% power. Unfortunately I didn't get that printout and the Unigroup guys are away at the moment, will try and get hold of it on their return. So, looks like a healthy engine to start modifying and the only real area of concern is the w2a heat exchangers which the aftermarket has plenty of solutions for    
    • I maintain it actually looked really nice in person. So much so that I thought "No, this is illegal" but there it was, clear as day. I think we can easily call the wing and wheels/height to be transformative. Not saying it's better than the GR Whatever, or the 86, or the WRX STI or anything of that sort (the internet says it all bolts up so you can buy best of all worlds?) but it's still at least a thing and not nearly AS bad as people say.
    • That's less offensive than the previous gen.....except for all that ugly black tupperware around the edges. Blerck!
    • I leant out the window recently and took a picture of this new WRX. It looked real damn fine in person. It's faster around a track (stock) than a (stock) GR Yaris. It's much more practical despite being heavier. It's significantly cheaper. This gen tunes really well, much better than others. .... I think they're probably a lot better than people expect.
    • WRXs are a pure pleb boring car these days. You need to get an STI to even get close to what a WRX used to be.
×
×
  • Create New...