Jump to content
SAU Community

Recommended Posts

hey people i need some advice,

i have a rb20det 5 spd in my S13 silvia....

tonight all of a sudden it started rumbling and it sounded exactly like a WRX boxer engine. it was making normal boost levels but the power felt lower and it was very lumpy!!!! i pulled over and had a look under the bonnet, when i gave the throttle a little twist, i could hear a sound like a hiss. i couldn't destinguish if it was an air leak or if it was like a squirting sound. (if you understand me?) but the sound was around the top of the engine where the intake pipe meets the throttle body. is this a common problem some people have heard? or will it be something to go see a doctor about???

after i stopped after and turned off the engine for 30 mins it was fine again. then it happened for about 5 minutes while driving home. what is thisssssss?????

any help would be appreciated.

Link to comment
https://www.sau.com.au/forums/topic/77208-rb20det-problem-wrx-sound/
Share on other sites

Dead coil pack dude! Guarentee it. Take off the plug cover and unplug each one individually. The engine will run even rougher on each one. When you unplug the one that makes no difference you've found the stuffed one :D

Mine did this when I imported it and as soon as it got warm the dodgy one would fail.

good luck.

I had the same problem but it was a spark plug,the ceramic bit above the gap cracked and slid down to cover the spark gap.Everynow and then it would back to normal,must of been the comp pushing it back up etc.

So yer as baselinez said coil pack coz it's not sparking.

Also spray carby clean around the inlet manifold(where the top/bottom meets)join and see if the idle changes.Could be gasket or maybe just tighting of the bolts.

I have had this problem many times and had many reasons for it.

As mentioned it could be a faulty plug or a faulty ignition coil or module. It can also be caused by a leak in the inlet tract.

As you heard a hissing sound around the throttle area I would be starting there first and looking closely at the rubber joiner for a split.

And while you have the crossover pipe off may as well throw in some new plugs.

Its gotta be ignition.

Mine comes and goes just like that on my RB26. Seriously just goes into Rexy mode, then 5mins later, goes to GTR mode. (GTR is better by the way, hehe).

It has to be ignition, because if it was a cracked seal or something it would be more constant, I think mine might even be the plug going into the module, hope its not a coil pack.

will a dud coil pack come and go though? cause today the problem seemed not existent. but i bet it'll go on the weekend again. also just noticed my clutch is starting to get very slippery, so thats more money i have to spend. is the RB sound really worth it in the end??? i'm thinking maybe an SR would have been the better option :D

just like almost the majority of contributors on this thread, i say that it is you coils. get them replaced.

(quote:'m thinking maybe an SR would have been the better option ) believe me, the RB is way better!

Dude, its basically the only problem the RBs have and its just due to age. Yes with my car the problem came and went until it stayed stuffed for good.

Do the test and it will prove if its them or not.

You can't blame a slipping clutch on the motor type :D Its just one of those things. Stick with it, the RB shits on the SR. One dud coil is the only problem i've had on mine in 6 months since I imported it. Fix it and you'll be fine! Keep us posted!

lol that was what i was like too, i was like: "hey cool i sound like a modded WRX!" then i started driving like miss daisy and worrying about it hahahah but i enjoyed the sound but not the rumble through the car etc.

i will try to suss out the coil packs on the weekend, and get back to you's!

Anyone?

Can you tell us how to test each coil?

Because if its going to be a matter of trialing each coil being swapped over, it could take 3 months, as its inconsistant whether it works or not. So I'll swap one, then wait a week, then swap the next one, wait another week or two and so on.

There must be some way to test.

Like he said, just unplug them one by one, if the one you unplug is GOOD the car will sound even WORSE, so plug it back in and move on to another until you get to one that when unplugged makes no difference, that's the cylinder that's down.

But don't just assume it's the coil, pull the spark plug out and check it (is if fouled? clean it and see if things improve), swap a pack around and see if the dropped cylinder follows the coil, if not to loom could be damaged, etc.

If it's a dud coilpack buy a new one, or if you intend to run high-boost in the future maybe think about a set of SplitFires (~$650).

I say again:

Because if its going to be a matter of trialing each coil being swapped over, it could take 3 months, as its inconsistant whether it works or not. So I'll swap one, then wait a week, then swap the next one, wait another week or two and so on.

This is relevant because the guy the started the thread and myself are NOT having the problem all the time, but would like to fix it before it comes an ALL THE TIME thing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've sent JaseR33 a private message in the hope he gets an email and contacts you
    • I have seen a case where the starter motor shorting against the casing caused a massive voltage drop + so much EMI that it caused all the sensors to spew garbage data at the ECU. Test the battery to make sure it has acceptable CCA/capacity first, I have gotten "brand new" batteries before that couldn't even power a 10W light bulb without dying probably because it sat in a warehouse too long without being charged. Only easy way to diagnose this 100% is put an oscilloscope on the battery and also look at key sensors to see if there's any clues.
    • There's a bunch of smaller shops that don't quite attract Singer money but are still hiring from that same pool of labor. Those are the body shops that you go to when you can't afford a Singer, but your old Porsche needs some serious bodywork. You can't exactly take those cars to the usual insurance body shops. When I say restomod, I mean they'll do something other than 100% OEM/OEM-equivalent aftermarket parts R&R. In the Porsche world this would be stuff like taking a 50k 964, doing a bunch of deferred maintenance/unwinding the nightmares the previous owners did to the car because a lot of people that own these cars tended to be penny wise, pound foolish types, then maybe some relatively simple off the shelf modifications to things like suspension, transmission, engine, headlights, etc. and you've spent 130k USD. When even the worst houses in the poor neighborhoods are worth 1M USD and the nice houses in wealthy neighborhoods are worth 3-10M USD suddenly 130k spent on a 50k car seems cheap.
    • Hoping to get a few ideas to help troubleshoot this issue, I'll try to keep it short.  A mate popped the motor in his 2018 LDV T60 with the 2.8 turbo diesel motor. He swapped it and I was his phone a friend when he got stuck.  The new motor is in, however it won't fire. The battery is literally brand new, when you crank it the volts very quickly (say 2 seconds of cranking) drop to 8 volts and the engine stops turning over. Watching the belts, I'd say they move about 5cm before coming to a stop. We put a booster pack on, no change.  The only potential issue I'm aware of is, when we pulled the motor the grounding strap was still attached. The strap copped a thrashing before we realised what was going on. It looks okay-ish but it's going to be replaced to rule it out.  The main challenge is, I wasn't there for 90% of the work. This is his first time doing any major work on a car and he was learning as he was going. He thinks everything has been put back together properly, however I'm not entirely confident that this is the case.  It would be good to get some ideas about what else to check. The car isn't spitting any codes so that doesn't help.  I've attached a photo, because why not lol.   
    • I mean an N1 came with a minimal paint thickness compared to dealer models. It’s probably had a ton of vinyls and stuff possible a race paintjob or two over the years. you don’t buy an N1 for its stunning good looks or comfort 🤣 you buy it to send it and measure how much air you can get on the hill at Bathurst
×
×
  • Create New...