Jump to content
SAU Community

Recommended Posts

I Just picked this up from the SHIFT PERFORMANCE website.

It is advertising a Apexi TURBO TIMER. Then in brackets it says "for turbo and NA Vehicles)" why would it advertise it for NA vehicles if NA vehicles are not TURBO.

why would people buy it?.. :confused: :werd:

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/
Share on other sites

A turbo timer just makes your car run for a preset period after you take out the keys, so the turbo has time to cool down a bit before it turns off.

Obviously it works on ALL vehicles. NA included, if one desired.

thanks mate

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1414414
Share on other sites

i use one. on my NA skyline. I dont see the harm in lettin my engine warm down after im hammering it at 120km+. i also use it to warm up my engine on cold days in the morning, for when im stoppin to get out and grab a newspaper or something else trivial, to measure my voltage when im running my stereo with the engine off, and for a couple of other reasons that im sure i could think of.

Dont say that NA's use them for wank factor cuz my reasons are all legitimate, and also their not illegal in WA.

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1414935
Share on other sites

']i use one. on my NA skyline. I dont see the harm in lettin my engine warm down after im hammering it at 120km+. i also use it to warm up my engine on cold days in the morning, for when im stoppin to get out and grab a newspaper or something else trivial, to measure my voltage when im running my stereo with the engine off, and for a couple of other reasons that im sure i could think of.

Dont say that NA's use them for wank factor cuz my reasons are all legitimate, and also their not illegal in WA.

are all turbo timers the same.

do i have to get a specific one to do what your one does with the cooling and warming up of the engine?

How does it warm up the engine? when you could just turn on ya car?

can you tell me how they work .............please ;)

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1420386
Share on other sites

Turbo timers are designed to simply let the car run for a desired period of time after turning off the key. Some of the new ones even have there own calculations on how long your car should run for. They were built for turbo cars, because turbos use the engines oil for cooling and lubrication, after "giving one a hard time" the oil temperatures rise dramatcially, letting the car run down gives the turbo and oil a chance to cool down as the oil is still flowing through the turbo. Shutting a turbo down straight away while the turbo is still hot allows the oil to bake on things like bearings, shafts and seals forming a hard abrasive substence causing huge wear and sometimes seizing the turbo.

If they were required on NA cars, drag cars would not shut down there engines as they cross the line, they are not beneficial to NA cars.

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1420462
Share on other sites

How does it warm up the engine? when you could  just turn on ya  car?

you just turn the car on and then turn it off to let the turbo timer keep the engine running, so you can leave the car running when you run in to get the paper etc on the morning, with out leaving your keys in the car, as most of them turn off when the hand brake is released

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1421598
Share on other sites

If they were required on NA cars, drag cars would not shut down there engines as they cross the line, they are not beneficial to NA cars.

:P

Right, so because a dedicated race engine that probably gets pulled down and rebuilt after every meet doesn't need something, then why would a street car that is expected to do hundreds of thousands of kilometres without stripping down have to worry about it?

Drag cars don't run air filters. I guess they're not necessary either.

FI race cars don't use turbo timers either, and no manufacturer ships with one. Clearly if they don't think its necessary in a race situation or to avoid warranty claims on street cars, they're not beneficial on FI cars either.

JGTC cars also run 12.x:1 compression and a fair whack of boost; want to try that on your street engine?

Here's a hint: never use what goes on with a race engine as an example of what's right to do in terms of maintenance and longevity for a street engine. Unless you can afford to replace or rebuild your engine as often as race teams pull down theirs.

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1421636
Share on other sites

I wasnt talking about top fuel cars or dedicated race engines, i was talking about big NA street cars that do, do a hundred thousand k's between rebuilds.

Holden Astra turbo's and a few others do come with turbo timers standard so that was also a bad example.

My point is they are not beneficial to an NA engine, and to date no one has been able to find a valid reason why they are.

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1422729
Share on other sites

they actualy do more harm than good to an N/A vehicle. :thumbsup:

on idle, the A/f mixtures are rich, which eventually washes any oil off the cylinder chamber walls, causing more engine wear....

Why do you think most car manufacturers recomend you warm up your car in the mornings for only 30 - 60 seconds??

It's beneficial for a turbo b/c the cost of saving the turbo outweighs the engine wear factor.

Even better are the pumps that circulate oil through your turbo after you have shut the engine down. I have yet to see one though....

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1422772
Share on other sites

whats the harm in letting a NA skyline's oil cool down for a minute or two, lolz let people do it if they want...its just like letting it idle for a few minutes while u go to ur gf's door and wait for her and then u find out shes not ready and u have to wait a further 10 minutes :bs:

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1422947
Share on other sites

whats the harm in letting a NA skyline's oil cool down for a minute or two, lolz let people do it if they want...

Why would an N/A skyline need to cool it's oil down?

Turbo's spool at up to 150000 rpm (maybe more), and it's when the engine is stopped that oil on the bearings starts to cook. The oil is not cooking itself, the hot bearing are.

Unless you have removed the rev limiter on your N/A so it revs to 150,000 rpm, you are doing damage, not good.

Have a read of this article . In particular look at the reliability section.

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1422988
Share on other sites

the purpose of the turbo timer is to keep the engine running, it wont cool the engine down for peanuts, if anything it will heat the engine up more as there's no airflow into the engine. however as the engine is running so is the oil throughout it, which leads to the oil feed on most turbochargers. the bearings get insanely hot during operation and letting the engine run on idle for a minute allows the oil feed to keep running, which cools the bearings and shaft down. i mean its still gonna be a few hundred degree's after the turbo timer is off but it will drop from maybe a high few hundred deg's to a lower temp by oil and water cooling. if you were driving around giving it some stick and then instantly turn off the bearings will just stop and shaft will too. so the heat stays in and can expand/warp or so forth I guess??

the purpose is to cool the turbocharger parts, not the engine itself

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1430336
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bloody Skylines, they put you through the bloody wringer! Stick at it! Stunning drag strip BTW! Where is it? Can see part of the name on the slip and probably should just Google it!
    • I mean the other day I had to walk someone through diagnosing why their timing belt was walking off the cam gears. At least one of the issues was a bent tensioner stud. Local mechanics have found runout on the CAS mechanism causing weird failures. I'm also no saint here I've documented some of the things I've had to learn the hard way. Something I discovered recently is that my CA emissions catalytic converters weren't even welded correctly to align the downpipe to the main cat and they tossed the support bracket that goes from the transfer case to the downpipe to support everything there. I spend a lot of time chasing down these decidedly unsexy problems and the net effect is it feels like I never actually get to the original objective (flex fuel, VCAM, oil control, cooling, etc).
    • At times with how you make everything sound, all I imagine Americans doing when they see a gtr is standing there looking at it and bashing it with a gun like how a caveman would with a club and hoping it fixes itself 
    • I think this is just a product of how the US market works for this stuff. Shops are expensive and there's no real way of knowing what kind of results you're going to get, people don't really have the institutional knowledge. I have heard too much at this point to really put faith in anybody "full service" except maybe DSport and they aren't really a full service kind of shop. If you go to the right place I have no doubt they'll get it right for you. Some locals have set it up right but the cost really is nuts and even now they're still fighting issues. And you know I'm a crazy person who thinks things like twin scroll, relatively short low-mount cast headers, PCV recirc to intake, recirculating BOV, right-sized for ~400 whp, MAF load, validating all of that to a standard comparable to OEM test programs, etc are relevant. For what it's worth, multiple local owners at this point have been stuck in a perpetual cycle of blowing a motor -> getting someone to rebuild it -> some missed detail causes the bearings to wipe and spin just outside of break-in mileage or drop valves or some other catastrophe -> cycle repeats. I usually only find out about this because I'm perpetually helping random friends with diagnosing car troubles, Skyline or otherwise. The single turbo stuff if I'm honest is mostly secondary, it just doesn't seem to achieve the numbers in the ~2000-3000 rpm region that I would expect given the results I've seen here or in Motive's videos. I don't really know what we're missing here in the US to be causing this. Lots of people like to emphasize the necessity of finishing the project first and foremost, but I'm not made of money and I can't afford to be trashing a 15k+ USD engine build with any regularity. Or spending my relatively limited garage time these days unable to triangulate problems because too much was changed all at once. Also, even if it isn't a catastrophic failure I would consider spending the cost of single turbo conversion with nothing to show for it to be pretty bad. 
    • The water pump is know to leak as well. So if the coolant is low checking that first as well as hoses. 
×
×
  • Create New...