Jump to content
SAU Community

Recommended Posts

I Just picked this up from the SHIFT PERFORMANCE website.

It is advertising a Apexi TURBO TIMER. Then in brackets it says "for turbo and NA Vehicles)" why would it advertise it for NA vehicles if NA vehicles are not TURBO.

why would people buy it?.. :confused: :werd:

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/
Share on other sites

A turbo timer just makes your car run for a preset period after you take out the keys, so the turbo has time to cool down a bit before it turns off.

Obviously it works on ALL vehicles. NA included, if one desired.

thanks mate

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1414414
Share on other sites

i use one. on my NA skyline. I dont see the harm in lettin my engine warm down after im hammering it at 120km+. i also use it to warm up my engine on cold days in the morning, for when im stoppin to get out and grab a newspaper or something else trivial, to measure my voltage when im running my stereo with the engine off, and for a couple of other reasons that im sure i could think of.

Dont say that NA's use them for wank factor cuz my reasons are all legitimate, and also their not illegal in WA.

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1414935
Share on other sites

']i use one. on my NA skyline. I dont see the harm in lettin my engine warm down after im hammering it at 120km+. i also use it to warm up my engine on cold days in the morning, for when im stoppin to get out and grab a newspaper or something else trivial, to measure my voltage when im running my stereo with the engine off, and for a couple of other reasons that im sure i could think of.

Dont say that NA's use them for wank factor cuz my reasons are all legitimate, and also their not illegal in WA.

are all turbo timers the same.

do i have to get a specific one to do what your one does with the cooling and warming up of the engine?

How does it warm up the engine? when you could just turn on ya car?

can you tell me how they work .............please ;)

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1420386
Share on other sites

Turbo timers are designed to simply let the car run for a desired period of time after turning off the key. Some of the new ones even have there own calculations on how long your car should run for. They were built for turbo cars, because turbos use the engines oil for cooling and lubrication, after "giving one a hard time" the oil temperatures rise dramatcially, letting the car run down gives the turbo and oil a chance to cool down as the oil is still flowing through the turbo. Shutting a turbo down straight away while the turbo is still hot allows the oil to bake on things like bearings, shafts and seals forming a hard abrasive substence causing huge wear and sometimes seizing the turbo.

If they were required on NA cars, drag cars would not shut down there engines as they cross the line, they are not beneficial to NA cars.

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1420462
Share on other sites

How does it warm up the engine? when you could  just turn on ya  car?

you just turn the car on and then turn it off to let the turbo timer keep the engine running, so you can leave the car running when you run in to get the paper etc on the morning, with out leaving your keys in the car, as most of them turn off when the hand brake is released

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1421598
Share on other sites

If they were required on NA cars, drag cars would not shut down there engines as they cross the line, they are not beneficial to NA cars.

:P

Right, so because a dedicated race engine that probably gets pulled down and rebuilt after every meet doesn't need something, then why would a street car that is expected to do hundreds of thousands of kilometres without stripping down have to worry about it?

Drag cars don't run air filters. I guess they're not necessary either.

FI race cars don't use turbo timers either, and no manufacturer ships with one. Clearly if they don't think its necessary in a race situation or to avoid warranty claims on street cars, they're not beneficial on FI cars either.

JGTC cars also run 12.x:1 compression and a fair whack of boost; want to try that on your street engine?

Here's a hint: never use what goes on with a race engine as an example of what's right to do in terms of maintenance and longevity for a street engine. Unless you can afford to replace or rebuild your engine as often as race teams pull down theirs.

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1421636
Share on other sites

I wasnt talking about top fuel cars or dedicated race engines, i was talking about big NA street cars that do, do a hundred thousand k's between rebuilds.

Holden Astra turbo's and a few others do come with turbo timers standard so that was also a bad example.

My point is they are not beneficial to an NA engine, and to date no one has been able to find a valid reason why they are.

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1422729
Share on other sites

they actualy do more harm than good to an N/A vehicle. :thumbsup:

on idle, the A/f mixtures are rich, which eventually washes any oil off the cylinder chamber walls, causing more engine wear....

Why do you think most car manufacturers recomend you warm up your car in the mornings for only 30 - 60 seconds??

It's beneficial for a turbo b/c the cost of saving the turbo outweighs the engine wear factor.

Even better are the pumps that circulate oil through your turbo after you have shut the engine down. I have yet to see one though....

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1422772
Share on other sites

whats the harm in letting a NA skyline's oil cool down for a minute or two, lolz let people do it if they want...its just like letting it idle for a few minutes while u go to ur gf's door and wait for her and then u find out shes not ready and u have to wait a further 10 minutes :bs:

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1422947
Share on other sites

whats the harm in letting a NA skyline's oil cool down for a minute or two, lolz let people do it if they want...

Why would an N/A skyline need to cool it's oil down?

Turbo's spool at up to 150000 rpm (maybe more), and it's when the engine is stopped that oil on the bearings starts to cook. The oil is not cooking itself, the hot bearing are.

Unless you have removed the rev limiter on your N/A so it revs to 150,000 rpm, you are doing damage, not good.

Have a read of this article . In particular look at the reliability section.

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1422988
Share on other sites

the purpose of the turbo timer is to keep the engine running, it wont cool the engine down for peanuts, if anything it will heat the engine up more as there's no airflow into the engine. however as the engine is running so is the oil throughout it, which leads to the oil feed on most turbochargers. the bearings get insanely hot during operation and letting the engine run on idle for a minute allows the oil feed to keep running, which cools the bearings and shaft down. i mean its still gonna be a few hundred degree's after the turbo timer is off but it will drop from maybe a high few hundred deg's to a lower temp by oil and water cooling. if you were driving around giving it some stick and then instantly turn off the bearings will just stop and shaft will too. so the heat stays in and can expand/warp or so forth I guess??

the purpose is to cool the turbocharger parts, not the engine itself

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1430336
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...