Jump to content
SAU Community

Recommended Posts

Do you want to have your hearing impaired ?

Do you like it when it feels like your ears are bleeding ?

Well if you answered "Hell Yer!" then this is right up your ally.

2 x Kicker (F12c) 12" Competition Class Subs in a custom enclosure.

The box is made from 3/4" MDF and is internaly braced and sound deadened. The box has been built to Kickers exact recommended specifications, it is divided in the middle to give each sub its own internal airspace of 1.75 CuFt and are both ported by a 4" tube port.

The box features a gold plated quick connection port for each sub on either side of the box which is connected by Stinger 10 gauge speaker wire & gold terminals. It is carpeted and both have a Kicker removable subwoofer grill.

Each sub is 4ohm svc (single voice coil) and is rated to take 400w RMS peak, or 200w RMS continuous.

The subs can be linked together to run off one channel.

If they are linked in parallel it will drop ohms to a 2ohm load so you amp has to be 1ohm stable.

If they are linked in series it will increase ohms to a 8ohm load.

The enclosure dimensions are:

Width = 31"

Height = 13"

Top Depth = 17.5"

Bottom Depth = 21.5"

The subs have never been run in a car.

When i brought them I ran a 4hr break in procedure which was done on a test bench and involved varying freq tone steps.

A very regretful sale .... $550

Link to comment
https://www.sau.com.au/forums/topic/774-kicker-subs-in-enclosure/
Share on other sites

It was goin to go into my hx kingswood, but i didnt manage to get that far, im too fussy and i wanted to custom the boot b4 it when in, but i ended up giving up on the car after i found rust in the rear quarter panels.

Haha, Prank you remember aggess ago a guy in Sydney from SDU was selling a sound setup with 2 x 12 " MTX boxed subs, pioneer splits, etc etc .... and you were after the subs ? I was the guy who purchased em, but I still havn't tried fitting them in the boot :) Maybe today is the day !!

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The cam I am actually putting in (a few posts up) is actually smaller than my current one. At least duration/overlap wise. All the chop stuff I hear just sounds like an engine running badly, because it is. I then envision driving it around in 1st gear and being massively sad about it bucking to the beat of said chop. There is an idle video of someone with a similar cam floating around the internet, but mine is a custom cam (so is his) so it'll never be the same, plus the fact exhausts are entirely different. What I want to do is put some bullet mufflers/race mufflers in to replace a couple sections straight pipes that currently replace the two extra cats that I don't need. But this is even further down the line!
    • I can tell you now, when the bracket that the little hydraulic ram attaches to snaps, with a subframe, and V8 from an AMG C63 on it, it sounds like someone letting shotgun off right beside you. It leaves your ears ringing, and a huge thankfulness that you never ever put a body part under something heavy that's only supported by a hydraulic lift...
    • Still not a guarantee fix. I used a high quality butyl-mastiq (the black goo that's not really silicone nor polyurethane, same stuff they use from the factory that just spreads out like melty cheese), and I still get lots of water on both sides of the trunk when raining or washing the car. I also suspect the factory spoiler rubber gasket might not be sealing well, so I'm thinking of adding a thin layer of grey silicone around the bolt holes on both sides and see if that's where it also leaks from. The biggest issue is that these cars don't come with a drain hole on each side like other coupes and hatchbacks.
    • I hate it, but maybe he could paint it Monster jam style and call it...godzilla?
    • Would seem to me to be appropriate to go GTR style bar. There are options with and without N1 vent holes, with the GTR lower lip integral (because FG copy). https://justjap.com/search?q=r32 bumper  
×
×
  • Create New...