Jump to content
SAU Community

Recommended Posts

hey peoples having problems installing the bosch 040.. ive got a r33 skyline series 2.. ive read a tutorial on the 989 or watever and yeah just few things im not sure of.

what im upto got everything off.. and hav found that the holder for the std fuel pump is way too small to fit the bosch 040.. so wat i have done is just bent the bottom bit straight and then just cable tied it to the pole.. is that alright to do?.

next thing is.. the positive and negative connectors to the actual pump.. ive stripped the wires and wrapped it around the connector and just put a bolt ontop of it.. is that ok? i have worries about it tho, cause the positive on the old pump was coverd with a black rubber however doesnt fit the new pump..

ive pretty much just replaced the std fuel pump with my new pump exactly. is that wat ur spose to do or are u meant to make modifications?. also ive found that the sock connected to the std fuel pump dont fit no where on the bosch 040.. am i spose to jus leave it off?..

what should i fix or be doing? thanks for your help guys.

Link to comment
https://www.sau.com.au/forums/topic/78236-bosch-040-install/
Share on other sites

most of that sounds right dude, there is nothing wrong with cable ties....they are designed to hold things and they do it well. as for the wiring....aslong as the positive is touching nothing but the postive terminal, it will be fine without the boot, the boot wouldve been there just to stop it coming in contact with anything. as for the sock....its purpose is to stop the pump sucking up any crap from the bottom of the tank....its probably a good idea to find a way to put it on or to think of something else..... even if you cut the adaptor off the sock and cable tie it directly to the inlet of the pump..

cheers

Linton

wazz....the fuel pump doesnt move around....i put a fuel pump in a mates 180, used cable ties....been over a year, hasnt moved at all....there is nothing wrong with zip ties. hose clamps can be over tightened and either damage the pump or the clamp, resulting in a useless clamp. why does everyone see zip ties as being dodgy??? why not get some aircraft grade T-Bolt hose clamps.

My opinion.....

1. Make sure the Bosch 040 is installed at the lowest point so it can be right near the bottom of the tank. Bending the cradle straight at the bottom is a good idea

2. Use electrical end terminals for the wiring part & soilder or crimp them.

3. Use nuts (stainless steel if you can) to place wire terminals on to pump

4. Use stainless steel clamps to hold the pump into place.

As for zip ties , I won't want that pump coming lose and the terminals moving about........bang.

I also wouldn't like anything contaminating my fuel, eg plastics, rust from metals.

Also the bosch 040 pump has a built in filter, no need for sock and the reason for it being mounted very low in tank.

Yeah I asked Bosch about the need for a sock on the bottom and they said it didn't need one. Stainless steel hose clamps are the go in my opinion. I bent the cradle out flat as well, then used the rubber base that the old pump was sitting on as a sort of 'cushion' to stop the 040 from making noise. Works really well, no noise at all until the car is almost out of fuel.

"The internet? They have that on computers now?"

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • In the US the EPA has been going after shops that sold aftermarket ECU tuning software that allowed you to disable CELs for things like EGR, DPF, SCR, or TWC failure. They also went after shops for selling emissions delete equipment. Their logic is that all cars built for street use have this emissions equipment and you cannot do an after the fact conversion to an off-road vehicle not intended for street use. Cobb, Hondata, and similar companies have basically all revised their tuning software such that going forward you cannot suppress DTCs for emissions-critical systems, nor can you toggle systems on and off in the tune like EGR. You also cannot adjust OBD emissions monitoring logic. You can still tune these cars. But you have to do things the hard way, basically. For example Subaru FA20DITs used to delete the TGV system to get spare analog IO for a flex fuel sensor. EGR also has to be dramatically pared back because without the TGVs the stock EGR map causes bad misfires. Now instead they have to implement the flex fuel system as a CAN bus sensor instead. IMO, this is heavy-handed but the EPA in the US gave so much leeway for so long and the aftermarket relentlessly abused that leeway to the point that they could actually see the effects of all these emissions-deleted work trucks on their air quality monitoring for cities that haven't met Clean Air Act standards. It's one thing to have a few people deleting emissions on their weekend car that spends 9 months out of the year on jack stands. It's another thing entirely for entire fleets of tradies driving around 8 hours a day on deleted diesels that emit 1000x the emissions per mile of a compliant vehicle.
    • Hmmm. that's a tough one. There's a lot of history bundled up in that lot. Perhaps instead we can create a new pinned thread, called "Legacy Pinned Threads" and provide links to the these ones that will be unpinned in there. And maybe put the names of the pinned threads that are linked inside in the tags so they can seen from the outside? Or something like? I mean, it's half a step back towards having a more complicated forum structure, without actually having it. But there's a reason that heirarchical architectures exist. They are logical, and if executed properly, make it easy to find something without having any upfront knowledge of where it would be , and without using a search function.
    • Can we unpin a bunch of dead / irrelevant threads from: https://www.sau.com.au/forums/forum/8-engines-forced-induction/ New players at home will scroll and think this forum is dead.
    • It's all about selling non-compliant emmisions stuff, and things like tuning stuff that makes your car have more emmisions, a very small percentage of modifications and tuning go into race cars, the vast majority of tuning and mods, like catless exhausts, or non-compliant cats, go into street cars with registration  Like a gun shop can only sell to someone with a gun licence, if they don't, they are fined and even jailed, and whilst a gun is totally different to a tune, or a catless exhaust, they are still illegal for a street car As for customers, it easy, they send a letter and tell them to show up for an inspection, like if someone says your car is to loud now, if they don't show up for the test, they can cancel rego, just like not paying a traffic fine This has been happening for years overseas in other countries  I'm in no way happy about it, but, I think there is definitely writing on the wall for modern cars with emissions standards, which will effect tuning shops, parts suppliers and end users And like other countries around the world, it is the government's that makes the rules and regulations for street cars with rego What would happen to a tuner or workshop if they were investigated about turning off stuff in a ECU IRT emmisions stuff like engine check lights for cats, or removing cats, or putting in a lower cell cat, this is apparently all illegal IAW modifications to registered cars, or, retuning the car so that with even stock emmision stuff still installed, but due to the tuning, or parts, like bigger cam shafts, it will now not pass the emmisions test Yes, I am going into a rabbit hole, but going off what other countries are doing IRT everything related to emmisions........cars, trucks, manufacturing, mining, modified vehicles are a easy target Meh, time will tell how it goes either way 
    • This^^^ 100%. Endless Male Attention. "buy a cool car, attract females". No reality is the opposite. "Buy a cool car, attract males".     
×
×
  • Create New...