Jump to content
SAU Community

Recommended Posts

hey peoples having problems installing the bosch 040.. ive got a r33 skyline series 2.. ive read a tutorial on the 989 or watever and yeah just few things im not sure of.

what im upto got everything off.. and hav found that the holder for the std fuel pump is way too small to fit the bosch 040.. so wat i have done is just bent the bottom bit straight and then just cable tied it to the pole.. is that alright to do?.

next thing is.. the positive and negative connectors to the actual pump.. ive stripped the wires and wrapped it around the connector and just put a bolt ontop of it.. is that ok? i have worries about it tho, cause the positive on the old pump was coverd with a black rubber however doesnt fit the new pump..

ive pretty much just replaced the std fuel pump with my new pump exactly. is that wat ur spose to do or are u meant to make modifications?. also ive found that the sock connected to the std fuel pump dont fit no where on the bosch 040.. am i spose to jus leave it off?..

what should i fix or be doing? thanks for your help guys.

Link to comment
https://www.sau.com.au/forums/topic/78236-bosch-040-install/
Share on other sites

most of that sounds right dude, there is nothing wrong with cable ties....they are designed to hold things and they do it well. as for the wiring....aslong as the positive is touching nothing but the postive terminal, it will be fine without the boot, the boot wouldve been there just to stop it coming in contact with anything. as for the sock....its purpose is to stop the pump sucking up any crap from the bottom of the tank....its probably a good idea to find a way to put it on or to think of something else..... even if you cut the adaptor off the sock and cable tie it directly to the inlet of the pump..

cheers

Linton

wazz....the fuel pump doesnt move around....i put a fuel pump in a mates 180, used cable ties....been over a year, hasnt moved at all....there is nothing wrong with zip ties. hose clamps can be over tightened and either damage the pump or the clamp, resulting in a useless clamp. why does everyone see zip ties as being dodgy??? why not get some aircraft grade T-Bolt hose clamps.

My opinion.....

1. Make sure the Bosch 040 is installed at the lowest point so it can be right near the bottom of the tank. Bending the cradle straight at the bottom is a good idea

2. Use electrical end terminals for the wiring part & soilder or crimp them.

3. Use nuts (stainless steel if you can) to place wire terminals on to pump

4. Use stainless steel clamps to hold the pump into place.

As for zip ties , I won't want that pump coming lose and the terminals moving about........bang.

I also wouldn't like anything contaminating my fuel, eg plastics, rust from metals.

Also the bosch 040 pump has a built in filter, no need for sock and the reason for it being mounted very low in tank.

Yeah I asked Bosch about the need for a sock on the bottom and they said it didn't need one. Stainless steel hose clamps are the go in my opinion. I bent the cradle out flat as well, then used the rubber base that the old pump was sitting on as a sort of 'cushion' to stop the 040 from making noise. Works really well, no noise at all until the car is almost out of fuel.

"The internet? They have that on computers now?"

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Unfortunately,  it feels like it's been on the decline for nearly a decade. Especially as wallet racing became popular with them(biggest wallet can pay off a car that wins). It seems like a different mindset kf ownership these days. But, hopefully people like yourself keep some of the skyline scene alive.
    • A bit of data is always good, beats the Facebook experts with their opinions Although the kWs aren't anywhere near what you are after, it should give you a good indication. I have Bosch 1480cc injectors, often called 1650cc (only when run at 4bar). I run mine at 3bar base so I don't thrash the fuel system. Up top, making 437kW with boost dropping, injector duty is at 69% on E80 (might have had some residual 98RON in there)  
    • I have some downtime due to winter, and just wrapped up converting the car over to flex fuel. We don't get E85 at the pump over here in Canada, but I will be running Ignite E90 Race gas. I'll be mixing it with 99-100 RON pump gas and shoot for 50% ethanol content, up to possibly 85% content if there's any noticeable gains. Here's the question. Most I'll ever want to hit is ~600rwkW. I've currently running 1200cc injectors and want to keep them under 90% duty cycle. As per some online injector calculators, I should be good with 1200's well past 600rwkw on E85. As per other calculators, I'll need 1600-2000cc's. The variety is rather amusing.  With you Australians having E85 at the pump, what realistic duty cycles are you seeing in those kW ranges on E50 & E85 on your injectors? Thanks, 
    • No issues here with my PRP gears in an OEM pump housing. I did confirm all housing clearances were to spec prior though. Cheers. 
    • Thread is a bit old but figured id give my input anyway just incase. Have had lots of water problems in my R32 and was getting sick of wet tools in the boot and water filling up half my taillights. I ended up finding that whenever my car had been repainted they didn't reseal the taillights to the body of the car so water was just flowing straight into the boot, this is amplified by all the water around the bootlid being directed down to the taillights so would get pretty wet whenever I washed the car or it rained. You could probably use silicone to seal them to the body but I think from factory they use a roll of automotive grade butyl rubber. Hopefully this helps you if that ends up being how the water is getting in on your car!
×
×
  • Create New...