Jump to content
SAU Community

Recommended Posts

hey, i have recently bought an r32 gts4, and have read on the internet that by taking out the fuse under the dash it will be in 2WD. But the problem is that when i do take out the fuse, my ABS light on the dash comes on. I have tested it and my ABS is disabled when the light is on. Is there a way i can wire a switch for the 2WD whilst also having ABS.

Oh and yea, i've already done a search

Thanx in advance :)

Link to comment
https://www.sau.com.au/forums/topic/78544-2wd-switch-in-r32/
Share on other sites

What Beer Baron said is correct. But the problem with running a switch to the fuse in the engine bay is that you have to turn the car on and off to swap between 4WD and RWD.

Running a switch to the fuse under the dash solves that problem, but you also disable the ABS. Most people don't care as they only go to RWD for burnouts etc and don't need ABS.

  • 3 years later...

sorry to reopen a old thread but thought it would be better then making a new topic

but i have a 33 gts4 and want to make it rwd for the drags so i can launch it quick and not worry about braking anything. is it just a 4wd fuse in the engine bay i take out ?

There is always a preload on the transfer case in a 33 or 34, just removing power or hydraulics isn't enough to back it off and you'll kill the plates. It also means that the attessa is quicker to respond in a 33 or 34 compared to a 32.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...