Jump to content
SAU Community

Recommended Posts

I have 3 roll cages that i dont need.

One is from an R33 and the other two are from r32 GTR's.

They are all 6 point cages with cross bar in back.

2 of them have complete padding and the other has padding in the rear section.

Asking $600 each. They are all in perfect condition want to get rid of them.

Call me on 0408064230 or e-mail: [email protected]

Thanx all

Link to comment
Share on other sites

what size is the tubing? looks close to 2 1/2 maybe 3"?

what grade of steel is it? mild, s/s(unlikely), chromemoly, 350, 450???

obviousely its all bolt up? How is it joined through the top section? with bolts or has it been welded and needs to be rewelded once put back in car?

Another quick question..In the 33's if you run straight past the steering wheel near door hinge, theres barely any room for hand movement around the standard steering wheel, that pic had an a/m wheel on it, do you know if this was to allow for the lack of room, cause i dont think you can legally remove an airbag wheel and replace it with a nonairbag sort.

Cheers.

Link to comment
Share on other sites

I am not sure about the grade of steel but the piping is about 2" and looks bigger with the padding.

Yes the car has an a/m wheel on it i am not sure if it will be a problem for the stock wheel of a series 2. it was ok with the series 1. wheel fro memory

and it all bolts up along the roof so is easy to install took about 2 hour's to remove.

Link to comment
Share on other sites

The cage bolts in, next to the front seat just under the back seat at the side's, and at the front where the floor mate's are. Anyone will have to drill holes threw floor and wheel arch's bolt or there would be no problems i can see with welding the them in either.

I Presume the GTR cages would fit a 32 as I was under the impression the inside dimensions were the same but if someone could verify that. that would help.

Tha cages are at the work shop so i have only a couple of poor pics of them in the car hope you can see them.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • That's true. However, this problem has started since the tuning. First time with the return journey from the tuning. But yes, the pipe was clogged with dirt and rust. That was certainly due to age
    • Great info @tidi0x  Will definitely be handy for others and maybe me if I decide to keep the shit box H pattern.
    • Bumping this up one last time.... I wanted to follow up on the clutch slave issue. I realized that what the issue comes down to is the pocket is flat milled, and the cylinder does not want rest flat. So in order to mount it correctly you will need to make a spacer for the fingers so the cylinder is floating. I took two plates of aluminum, drilled some holes and was good. I did still need to make the relief cuts in the bell housing, as even with the spacer the bleed section still interferes. The OE bell housing the mounting holes are raised from the housing.       
    • If the event in USA goes ahead will be interesting as it seems the rules will get more cars over here. Apparently the track is laguna seca too. Yeah s15, if I get a the lower dash trims, centre console and change front cross member to standard LCA position will fit clubsprint. See how rules are as i would rather do complete widebody than a bolt on flare to run the 295 with proper clearance.
    • If the car is legal height I can't see it being an issue. Found a thread on reddit that might offer some insight.   I got a ticket from a copper in QLD for my S15 being too low. They had this wheel thing on a stick that they put under the car and it hit my exhaust. Anyhow went to an exhaust shop to get the exhaust tucked up/hung a little higher and I wound the coilovers up a smidge. Don't think I even had to go back to the police station unlike when I got defected for having a carbon bonnet when I brought the S15 from the ACT to QLD and had to replace it and then rock up at a police station and have a yougish female officer who knew nothing about cars confirm that I had changed bonnets. Should have just painted the carbon bonnet yellow to match the rest of the car lol
×
×
  • Create New...