Jump to content
SAU Community

Recommended Posts

I have used the nulon g70 addtive, and I noticed that it made absolutely no difference at all. It did not make it better when warm or cold.

There are two schools of thought floating around sau

1. nulon g70 contains teflon, which lubricates better, making gear changes smoother, and diffs less noisy.

2. nulon g70 contains teflon, which is TOO slippery and makes the synchros slip.

I've thought long and hard about which one is in fact correct, but my own experiements with it have not yielded any positive or negative resutls. Perhaps someone like sydneykid can comment on it.

A friend of mine put some of this stuff in his S13 and its known to pop out of gear at times (2nd gear inpaticular).

This only happens when theres a few g's on the car, such as during dorifto :)

Is that what you mean by synchors slipping?

Hi , i used some in my GTS4 and it improved things a little- its not a miracle gearbox fixer, a bit smoother gear change when car is cooler. Dont know if it has helped those 7k gear changes, maybe I 've improved my technique a little too. My car does not jump out of gear, I think the silvia gearbox has problems that are not related to additives.

I added some of this to a gearbox that had worn the hard casing of the input shaft to try and cut the noise down a little.

I think it made a small improvment to the noise.

Otherwise i wouldn't say the shifting changed at all.

If you run a mix of gearbox oil and auto tranny fluid you can get a nice shifting box under most circumstances. Alot of people i know run various ratio's such as 60/40 70/30 etc of the two oils with great sucess.

I would probally run a similar setup, but i need to keep the noise minimised. So i need to keep it thick as possible.

AFAIK its some valvoline oil.

Its about 500kms fresh

What  oil do you have in the box?

Should be something like Castrol VMX80 or equivalent.

That oil is designed for boxes that have cold shifting problems. (i.e. Nissan boxes)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all. I am aware there is lots of discussions about jacking points, where to lift the car and what not. But as usual just a lot of "in my opinion" and nothing definitive, and everyone does it in a different way. I want to hear from some experienced people on which points on the car it's okay/safe/recommended to lift the car using a four point hoist/lift. I will attach some images of my underbody. Sills are largely okayish, the driver side jacking point is pretty mangled though and it looks like the underfloor is slightly pushed in too, but I might be wrong. In the German Skyline forum, the consensus is to use the sidemember chassis rails in the front and the rear subframe? bushing in the rear. I know the manual says to never use the sidemember for loading but lots of folk do it and it was definitely done on my car too as they are slightly bent too. Based on the images, what points do I use to not make the already present damage worse? I'd use wood or rubber blocks to spread the load across a bigger area of course. Driver side sidemember and jacking point mangled one) https://imgur.com/a/eKjzrJX Driver side rear jacking point https://imgur.com/a/W3DWF1P Passenger side sidemember and jacking point https://imgur.com/a/65UvIJe Passenger side rear jacking point https://imgur.com/a/h3k7j53 We can also see some underbody rust but so far it all looks somewhat treatable and nothing that requires a Yoshida style restoration.
    • Have you put an aftermarket oil pressure gauge on and verified your oil pressure?   Noise being on the block, on exhaust side, how high up the block does it seem to be? It could be the VCT system getting cranky, especially if it's mainly at idle, and when warm, as that'll be your lowest point for oil pressure. Could be showing that oil passages / VCT solenoid are blocking.
    • Well, hydraulic lifters will get noisy if they are dirty/fouled in some way, and exactly how that manifests will depend on exactly what schmutz is where. There is a procedure on here somewhere for dismantling and soaking/cleaning them. Replacing them with new is about 50% of the work and about 5% of the money!
    • Thanks for the reply @GTSBoy this is is a hydraulic lifter engine. Yea right i did not realise the lifters were supposed to be compressible while installed. I could push them down but i had to lean almost my while body weight on them.  I have never heard of a lifter/ lifters ticking only at hot idle and getting worse the hotter it gets. I have owned a few jdm cars with noisy lifters. This noise is slightly more subtle, it is more of a sharp gentle metalic tic than the solid and more loud tapping I've heard on lifters. I have used a metal rod, alloy tube, hose and stethoscope and could not find the source of the tick. But it appears to be loudest on the actual engine block behind the exhaust cam gear and next to the oil filter. I had mate (40 year old mechanic) go over it with me and he couldn't find it either..  Could it be a cam seal issue of some sort?  Cheers  
×
×
  • Create New...