Jump to content
SAU Community

Repost - Desperatly Need Loom!

Ska

By Ska,
in Queensland

 Share

Recommended Posts

Ska Grand Master

Ska

Posted
Posted

I know this is a repost but I really need the wiring loom from the ignitor pack to the coils for a Series 1 R33.

Anyone know where I could find one, I have rang up about a dozen wreckers and have had no luck :)

http://www.skylinesaustralia.com/forums/sh...ead.php?t=73450

Has to be Series 1 and looks like what is in the pic attached, thanks!

Link to comment
https://www.sau.com.au/forums/topic/79484-repost-desperatly-need-loom/
Share on other sites
Ska Grand Master

Ska

Posted
  • Author
Posted

also pics of coil pack:

http://www.skylinesaustralia.com/forums/sh...909#post1449909

And help needed on wiring if you are an auto electrition, any help would be nice:

http://forums.skylinesdownunder.co.nz/show...&threadid=44280

hungry6 Experienced

hungry6

Posted
Posted

Ill give you the cam cover loom, but I can't give you a hand to wire anything, I'm not an auto electrician, but i did worked on a merger of an rb26 with an rb25 loom so a modified rb26 loom in a gtst with other mods. Since I broke my leg, I haven't been able to move around freely to finish of my own little project.

But u can have what ever bit that remains of the 2 looms

Ska Grand Master

Ska

Posted
  • Author
Posted

Yeah I dont need any help wiring it up, just need the loom.

But check out this thread first to see pics of what I am after, dont need the plastic cam cover, just the wiring that goes from the ignitor pack to the coils.

Sorry to be particular but have bought looms off people claiming them to be series 1, but they were series 2 unfortunatly.

51jay Mentor

51jay

Posted
Posted
Ill give you the cam cover loom, but I can't give you a hand to wire anything, I'm not an auto electrician, but i did worked on a merger of an rb26 with an rb25 loom so a modified rb26 loom in a gtst with other mods. Since I broke my leg, I haven't been able to move around freely to finish of my own little project.

But u can have what ever bit that remains of the 2 looms

Tough about the leg....know how you feel. Wjth regard to the above would it be possible to call in and see you on Friday

hungry6 Experienced

hungry6

Posted
Posted

Yes my car was a series one r33 which I owned it for about 10 years now, I wouldn't even call it a r33 anymore, project gone mad, lol.

yeah, it's a r33 s1 your car would have to have the 80mm afm (green sticker) as with the later rb20s?

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By TurboTapin · Posted

      Do the following first and get back to us. - Clean and verify your IACV - Verify for vacuum leaks/post MAF leaks. (Pressure test is the best and cheapest way) - Do you have a BOV with stock ecu/MAF? If so, remove it.     
    • DRoc81
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By DRoc81 · Posted

      Hey all, The skyline I have is stalling when the engine is at normal operating temp.  When starting it while it is cold, it'll run just fine.  I have replaced the battery (bad cell), I have replaced the fuel pump, fuel filter and clean the MAF sensor.  Any other suggestions?
    • DRoc81
      Shifting questions

      By DRoc81 · Posted

      Thanks for all the information on this.  I tried ordering the parts from Amayama website and all 3 Solenoids are discontinued and not available.  Does anyone have any other websites to suggest that I could find the parts?   Separate issue-- I will start a new thread, but basically the vehicle is stalling when warmed up.
    • TurboTapin
      RB25DET Solid lifter conversion

      By TurboTapin · Posted

      It's unfortunate what Tomei USA has done to Tomei's name in general. I'm very weary of ordering parts from them now. I only order direct from a Japanse source (e.g Nengun). At least their logos are different, so you end up knowing what you have. 
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Update Issues 5 (plus #4) - 10 After making a claim about issue #4's missing part, DeAgostini Japan sent a whole new issue #4 and it arrived about 2 weeks after that. That was back in early March. It took another 4 weeks to receive issues 5 - 13 though. This update is for issues 5 - 10. Ove the 5 issues the front left suspension and most of the engine have been completed. The quality of the castings and fit of the parts is quite good, it seems better than DeAgostini's BNR34 Skyline GT-R from the Fast & Furious 2 movie, which (to me anyway) doesn't seem to have as tight tolerances or quite as accurate castings.  Each issue has a lot of info about the 1989 - 1993 Skyline range and other Nissan models from that era, but the focus is on the BNR32 Skyline GT-R Nismo and the various racing it did in Japan, Europe (Spa 24hrs) and of course Australia. I've included some text translated with Google Lens in some photos and will add to them if there's anything worth including. 
×
×
  • Create New...