Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

Huddy, I run a RB20DET in my Zed with the GT25-440Hp & it is sweet, currently running std computer with fcd, and it makes 201rwkw@15psi. also have the same turbo on my R33 and it makes 240rwkw at 15psi. there is a lot of adapting to get it to fit/connect but I find it a great option.

cheers

As stated, 2510 on my car. Its definatley not a 2530

Has made a best of 208rwkw, makes peak power at 6500rpm, drops of a little after that, but only 10kw or so

When I first put it on, i had standard injectors and re-chipped ecu, but as the injectors where maxed out, no more power could be had

Running GTR injectors and PFC now, and with the bigger injectors we could add heaps more fuel in the mid-range and wind in more boost

I have attached the first dyno of when I did the injector upgrade, you can see the extra power that was made mid-range! Boost was 1.3bar, but dropping of to 1bar up top due to bleed valve

Running a PFC boost controller now, so it hold power up top more

If I had the choice, I'd run a 2530 if I had to do it all again, or a TD06 like Roy has

yeah, very happy with the PFC, with the whole car really. Sure, a bit more power would be nice, but its only a dyno figure, and a few seconds at full noise can land you in a bit of trouble lately, so its a good compromise

I had it down the 1/4 with the first setup, ran 14.3 at 104.9mph, with a 2.4 or 2.6 60ft, I cant remember

I have done 2 runs with the new setup, but the meet was called of due to rain, so my first run was 14.3ish at 103mph, and my second run was a 14.03 at 102mph, but it started to rain just as I was half way down and changing into 3rd, so it spun the wheels a bit and it showed on the times

Confident it would run a low 13 given the right lauch etc

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 1. Factory knock sensors for now, honestly the RB26 OEM knock sensors seem ok as they're flat response instead of resonant type but they appear to be internally grounded to the block. If I do replace the sensor it would just be to get ones that are not internally grounded so a differential input can be used to reject common mode noise. Definitely plan on fixing this as a part of the tuning process. 2. Never deliberately induced knock, though I guess I could try that experiment if I really wanted to. 3. All of this is basically on a stock engine + ECU, only modification is HKS GTIII-SS turbos and a Nismo plenum. Currently I run it with the wastegate solenoid unplugged so it won't try to raise boost past wastegate pressure.
    • After being peer-pressured into paying $100 for the MW remakes, got BO6 on XBox Game Pass. I think that's worth it.
    • That's a given!  Bit hard to powdercoat it properly without removing them! 😁
    • No detail on compressor or turbine sizes, which doesn't help with housing size selection with that kit. However, from SR20DET mucking about and money torching perspective, a GTX2860R Gen 2 w/ 0.64 (46mm inducer) will do ~260kW on E85 about 1.5bar of boost. All in before 3000pm, which cause a gearbox to shatter. Now imagine the same turbo, on a modern motor with an extra 0.5L of displacement, and heaps of cam timing adjustability (not an on/off affair like the Nissan shit boxes). If this was my car (which I would never own or consider buying, ever!), I would go for a nice twin scroll setup, and a G30-660. Gates plumbed back, no silly shit. Lean on the cam timing, big displacement to create a flat-ish torque curve.  
×
×
  • Create New...