Jump to content
SAU Community

what wheels are these???

lowflyer
 Share

Recommended Posts

Sydneykid Grand Master

Sydneykid

Posted
Posted
Can anyone tell me what wheels these are? They are 16 x 7" fitted to a R32 GTR with 20mm adaptors so they must be made for another Jap car?

I like the look of them as they resemble the Minilite wheel of the 60's.

I think they may be Panasport but not sure.

Thanks in advance

Are you sure they are 7"?:D

lowflyer Enthusiast

lowflyer

Posted
  • Author
Posted

Thanks for the info on the wheels guys.

They may very well be 8"wide but I am sure the salesman said they were 7".

I agree it doesn't make sense to use 7" on a GTR but they definately had large spacers fitted to move them outboard so they looked wider.

Does anyone know where you can buy these wheels and if they are available in 17 x 8" or 17 x 9" ??? I did a seach on the net but didn't have any luck.

yeah, why would you use 16x7's on a GTR when gtr's are stock 16x8??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Duncan
      NC MX5

      By Duncan · Posted

      Quite right, if you make it to that pension you deserve every cent
    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • MBS206
      RB20DE NEO smallbox clutch.

      By MBS206 · Posted

      From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • MBS206
      Lock up the old for sale / wtb threads.

      By MBS206 · Posted

      That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
×
×
  • Create New...