Jump to content
SAU Community

Cusco Master Cylinder Stopper

Memph
 Share

Recommended Posts

Memph Proficient

Memph

Posted
Posted

I have just installed one of these into my R32...

Visually. it definately moves "less" (still does move a little (Whole cusco stopper sorta moves with it))

But in the car the difference is minimal...

My question is. The adjustment screw in the brace that screws up against the master cylinder, how tight should that be?

Must admit im a little dissapointed with the result.

Anyone else with better experiences? ideas on anything i may have done wrong?

Cheers guys.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/81856-cusco-master-cylinder-stopper/
Share on other sites
SLY33 Mentor

SLY33

Posted
Posted

yeah just wind it in so it just touches.

Straight away i noticed a more positive pedal, maybe you expected too much, or maybe your standard brake lines and/or fluid are due for replacement, or you have bad pads or a comination of all of the above. if you want to get the most out of the std setup, get some good pads, braided lines and good fluid. Even try giving them a bleed.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • eli995
      NPboosted manifold fitting purpose

      By eli995 · Posted

      Ok gotcha, so one post to fpr  another to bov  and I have the mishimoto boost controller and a link g4+ so I’d just have the tuner set it up properly. For the last two from plenum post throttle to  ecu/ boost controller, I know that I have a hose coming from the ecu that I was confused about so I assume that’s what connect to the boost controller from the ecu? And then the last is just from plenum to boost controller then to wastegate?
    • eli995
      NPboosted manifold fitting purpose

      By eli995 · Posted

    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      From there, it was just a quick electrical check, prime the oil and start her up Which, is not what happened. 1. Bloody seppo Aeropro battery holder. Not only was it too tall for the battery (which I'll forgive them for, I have another battery the same nominal size that is taller than Neil's one, but the bracket is a fixed height so the battery was spaced up) But the thing that really shits me is the hardware to hold it on requires a 7/32 Hex key. WTF. No-one will ever be able to remove or install the damn thing without a hex key they don't own 2. Kill switch no longer worked once the console was installed. Neil mentioned above he had to adjust the length but it no longer cleared the console once installed. Sorted. 3. Suspiciously, the brake light holders were hanging in the boot with no globes. Sure enough the stopper on the brake pedal was missing so they are always on unless the kill switch is activated. Will pick one up tomorrow (turns out 32 and 33 don't use the same stopper) 4. All that sorted, I turned on the kill switch, turned the key to ACC. Nothing. Turned it to IGN. Nothing. Checked some fuses and found the main IGN in the boot was missing which improved things once it was replaced. Now ECU and dash lights turn on with IGN but still no fuel pump. 5. Turned it to Start....ECU on, no fuel pump, no starter. Plus the voltage dropped straight to 9v.  I suspect the starter is f**ked but am going to have to work through it all and see what is happening, really looks like more than one issue. Does anyone have the R33 fuse box key with the circuit it sources from (eg BAT, ACC, IGN, SRT etc) and supplies? I can find a translated list showing Amps and circuit without supply circuit, and I can find supply circuit without Amps and target circuit.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      3rd time lucky, the AAC is now all plumbed up after getting some final fittings All set up under the plenum of maximum access
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, so the weight has been bugging because it was really low. I did it again today and got a more believable answer at 1246 without driver And with a 93kg driver I'm pretty sure the car was still slightly on the quickjack last time meaning the full weight was not on the scales  
×
×
  • Create New...