Jump to content
SAU Community

Recommended Posts

Im putting these 4-pots on the front

using Wilwood Superlite bp-10 pads

going to make these billet aluminium 4 piston calipers fit !!! (bolts/lines/clearances)

dont care how I do it they are going on....

ooh yeah.

post-18854-1244690480_thumb.jpg

:P

Pretty flash mate

You will need to design and get milled a set of adaptors out of alloy or something to get them to bolt on

I would also look at bigger diameter rotors while you are at it

Maybe some bigger brembo GTR rotors. I think they are 328mm or similar?

Will they fit under your 17" r34 GTT wheels?

Pretty flash mate

You will need to design and get milled a set of adaptors out of alloy or something to get them to bolt on

I would also look at bigger diameter rotors while you are at it

Maybe some bigger brembo GTR rotors. I think they are 328mm or similar?

Will they fit under your 17" r34 GTT wheels?

Great work Tangles 324mm will fit under 17in,NO hope with 328mm,

lol not sure what you are on today chuckie?!? 324x32 is brembo gtr size and a good cheap choice for common disc size. tangles you'll need custom brackets to suit but from steel not ally. it may end up expensive because the adapters can be $$ couple of hundred each.

330ish is fin under 17s, 355 can fit but requires the right wheels and will be very tight. so 324 brembo size is a good choice.

lol not sure what you are on today chuckie?!? 324x32 is brembo gtr size and a good cheap choice for common disc size. tangles you'll need custom brackets to suit but from steel not ally. it may end up expensive because the adapters can be $$ couple of hundred each.

330ish is fin under 17s, 355 can fit but requires the right wheels and will be very tight. so 324 brembo size is a good choice.

Was & earlly SMOKE&JOKE :) ,Good JOB it wasn`t CRACK PIPE :):wacko:

Will have a look at 324mm with some DOGBONE`S on stag at some time ,may be when RB30 is done :w00t:Here`s a few of R32 caliper`s i have had rethearded to 14mm series2 bolt`s just have to get some line`s sorted & will fit then up & see if these`s are any better then STOCK 2POT`S,,cheer`s chuckie

post-36964-1244734394_thumb.jpg

post-36964-1244734526_thumb.jpg

post-36964-1244734574_thumb.jpg

post-36964-1244734671_thumb.jpg

Edited by chuckie

......mmm rb30......

anyway.....the gtr brakes will be heaps better, easier to find pads and rotors for, and cheap. I went with the G4s because I wanted new all round but before that I had the GTR gear on mine.

Was & earlly SMOKE&JOKE :) ,Good JOB it wasn`t CRACK PIPE :):wacko:

Will have a look at 324mm with some DOGBONE`S on stag at some time ,may be when RB30 is done :w00t:Here`s a few of R32 caliper`s i have had rethearded to 14mm series2 bolt`s just have to get some line`s sorted & will fit then up & see if these`s are any better then STOCK 2POT`S,,cheer`s chuckie

You'll love em, I certainly like the improvement on my car. I also just fitted a UAS Brake stopper and that has made a noticeable difference to hard stopping, e.g. brake pedal feels a bit firmer.

Only thing I am missing now is some steel braided lines. How are you going to approach brake lines Chucky? I have thought of going to somewhere like race brakes and getting a custom set made up but I am thinking if there are a number of people after brake lines it might be worth organising a group buy.

I got a quote from Maltech in March last year for replacement S1 lines - $495 inc GST & postage.

Couldn't justify it at the time, but now I've bought a set for the Z the Stagea has moved further up the list.

:)

lolz

Im already running Maltech braided brake lines, so will simply use an adapter piece to make 2+2 fit together

plus I already have a set of larger slotted rotors that I grabbed a yr ago for $50

got these Panoz 4-pots off ebay, searched Panoz Wilwood !! I paid $150aud delivered.

as good a deal as brembos surely

with pads being 120 deliv its under $300 so far

rims are BJR Grafic 17x7.5 +38 with 5mm spacers

definately going to make them fit -

post-18854-1244770455_thumb.jpg

post-18854-1244770471_thumb.jpg

post-18854-1244770479_thumb.jpg

post-18854-1244770487_thumb.jpg

just had a quick search

www.wilwood.com

They look nice

http://info.wilwood.com/BrakeKits.aspx?yea...&model=350Z

They do a kit for 350Z, so they will fit M35's??

They do a kit for 240sx(our 200sx with out a turbo) as well. . . hmm wonder if they will fit the C34

Looking on ebay.com, looks you can new calipers for $165us each?

Need to do a bit more research

these were used / made for Panoz Racing and used on the rear of a nascar (?). guy had 4 sets, they went real quick.

love my ebay

:)

will use my trusted engineer shaun at BoostWorx DynoTuning & Engineering to fit.

edit: could be outlaw 4000-series

more research coming up !! lol

p5.pdf

Pretty flash mate

You will need to design and get milled a set of adaptors out of alloy or something to get them to bolt on

I would also look at bigger diameter rotors while you are at it

Maybe some bigger brembo GTR rotors. I think they are 328mm or similar?

Will they fit under your 17" r34 GTT wheels?

Great work Tangles 324mm will fit under 17in,NO hope with 328mm,
lol not sure what you are on today chuckie?!? 324x32 is brembo gtr size and a good cheap choice for common disc size. tangles you'll need custom brackets to suit but from steel not ally. it may end up expensive because the adapters can be $$ couple of hundred each.

330ish is fin under 17s, 355 can fit but requires the right wheels and will be very tight. so 324 brembo size is a good choice.

324mm with 33gtst calipers only JUST fit under 34GTT rims, can't say about those other calipers but I would imagine it would be pretty close.

Aftermarket 17's with more offst would probably fit bigger but not the 34GTT rims.

They do a kit for 350Z, so they will fit M35's??

Yes.

Kit part numbers for M35 (Z33) are

NS01 (front) - SL6 BB Front Hat Kit

NSR01 (rear) - FSL4 BB Front Kit

Brake lines are required;

220-7016 (front)

220-9197 (rear)

I like them alot!

  • 3 weeks later...

z32 brakes are the same as R32 gtst brakes, depending on the series. they are a 4 pot caliper but run on a smaller 280ish mm rotor. i'm sure you could get them to bolt up, most of the calipers share the same mounting hole centers, but i dont think they would be much of an upgrade. best go for some R32 GTR/R33 GTST brakes, or even better R34 GTT's

Edited by QWK32

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The MX5 has had some annoying rattles in both front doors over bumps So I installed fancy pants door bushings, which stopped all of the rattles with the windows up, but........with the windows down there was still rattles, so after some googling,  and a chat with MX5 Mania, I got some new door to glass weather seals, all the rattles, windows up, or down, are gone now Shout out to MX5 Mania, the weather seals were on sale, and when I head to Dural to pick the up they even fitted them for me for free I did see a "really" nice Blue NA sitting out front   and this Black NC PRHT that looked like it has sat in the sun for its whole life and never had a wash, the clear coat was non-existent, an it looked horrible, really horrible, but, it had a nice turbo kit with over 200kw, the thing went like a cut snake, bagging the rears through the gears and dosing like a champ 😍 But, as I've always stated, I am keeping my NC na, I'm happy with the current power the car makes In other news: MX5 Mania do a drive in drive out turbo kit, the only minor additional part recommended for boosting my car, as it sits now, is a oil cooler, and that bonnet vents are definitely required for track use Aftermarket version look a bit to "racecar" spec I wonder how Focus RS bonnet vents would look?????
    • Paint is only structural when applied to the outside of Chinese and Indian cars. Otherwise it should never be present between mechanical joints that were intended to be metal to metal. Pain slips, slides, cracks, compresses, and add thickness that wasn't intended to be there. It comes firmly under the category of "just no".
    • appreciated it thanks   There are threads on the adaptor. I rear re anodising but didn’t know it will reduce strength   re mating services needing to be flat/ not painted, why would that be? I am devastated as car been off for a year, fixed power steering then installed bm57 master cylinder and just before driving it this came up. So annoyed   worried and afraid to drive it, no fun caliper coming off    
    • Just report the OP (via the 3 dots menu at the top right of post) and request deletion.
    • And boosters can be rebuilt by the same sort of brake shops that will rebuild a brake booster.
×
×
  • Create New...