Jump to content
SAU Community

Recommended Posts

EDIT 3/8/05: Problem fixed for now - see post 12 below.

Been having a bad run with the line,

Had a minor bingle about 2 weeks ago, car was running fine after (only front bumper was rooted) so the car was sitting in my garage and not started for 1 1/2 weeks. Go to start it yesterday and battery was dead, no prob, it was on the way out for a while and I already had a new one. So I replace the battery and go to start it and when I hold the key in the start position I get this loud Click, Click, Click, Click, Click, Click, noise at about 5 Hz, comming from the somewhere up front. The motor does not turn over at all.

When I hold start the voltage drops considerably - I know the battery is good, besides I also tried to start the car with the car jumpered to another running car.

All this sounds like a rooted starter motor to me, but before I spend craploads on a mechanic trying to find out what is wrong - has anyone had a similar problem? Does anyone know what it couls be?

Any help greatly appreciated.

i had the same problem iwth mine when i imported the r32. i thought it was the alternator but when i took it to the auto electrican he found out the it was some weird fuse ive never heard of before or something. if i were you i would take it to the auto electrician. get him to ring you once he knows what the problem is then you can decide from there. im a cheap arse and if it was the alternator i would have bought a second hand one instead of paying a shitload for a new one

It seems to be a problem in the starter circuitry. When I had that problem, my mech re-wired the starter solenoid so it got power direct from the battery (used the factory trigger wire to switch a relay). Haven't had a problem since.

Thanks for the replies, few things for me to try.

I forgot to mention that it used to do it when my battery was low, so BBQ's reply is sounding like its on the right track.

I have had the same issue, but mine did it also when there was plenty of voltage (seen from PFC). I always figured the starter motor was not engauged right. All I do to fix the issue is move the car a little while in gear the the problem goes away.

I dont know if I am right with my theory but it works for me...

I thought of doing that but then I thought that the startor mortor is not engaged unless it is being cranked. I'll give it a go if it worked for you.

I have had the same issue, but mine did it also when there was plenty of voltage (seen from PFC). I always figured the starter motor was not engauged right. All I do to fix the issue is move the car a little while in gear the the problem goes away.

I dont know if I am right with my theory but it works for me...

I have had the same issue, but mine did it also when there was plenty of voltage (seen from PFC). I always figured the starter motor was not engauged right. All I do to fix the issue is move the car a little while in gear the the problem goes away.

I dont know if I am right with my theory but it works for me...

Mine does the exact same thing.. a couple of times a week I have to give it a bit of a clutch start..

That clicking noise is the noise that it will make when the battery cannot supply enough CCA to the starter motor (Cold Cranking Amps). It makes this when enough voltage is present to turn the vehicles circuitry on but not enough to crank the motor. Check your battery voltage and then if that doesnt work get your wiring to your starter motor checked. If the starter motor was rooted I doubt it would even make a clicking noise.

I seem to have fixed the problem, I just played around with the power connections to the starter motor and gave them a quick cleen - have not had a problem since (3 days later).

Thanks all for your help, if this fourm did not exist I may have payed $200 for someone in a workshop to do the same thing.

Cheers,

Pat.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Sadly I can confirm if you are actually seeking to drift, you will quite easily spin up one wheel. Even if you're going in a straight line. I am not entirely sure of the metrics/terminology here but there's only a certain amount that the helical will actually spin both wheels. I've seen it on video with my own car where two lines of smoke switch over to just one after you really get in to it. Unlike with a clutch diff where you can keep your foot planted until the car regains grip, in my experience with the helical you want to be utilizing traction control allowing LIMITED slip or lifting (partially) when you start to spin up both tyres with a Nissan helical. Which makes them pretty sub optimal for drifting duty. That said... this is probably a helical on numbers alone. Just put the Kazz in
    • Let's just fix the problem by f**king the rest of the gearbox.
    • Unlikely, as per Greg's post. This is not helical diff behaviour unless one wheel is up off the ground. Shimming what? You don't "shim" a mechanical LSD. Probably not in the sense that you have heard of people "shimming" a diff. And the process that Nissan f**kwits call "shimming" a diff involves super-preloading a VLSD cartridge against the side of the diff to create a friction/wear point (in a place that it wasn't supposed to have one) to make the sloppy, useless, viscous diff into a hybrid viscous/mech abortion. In case it isn't clear, I consider the process to be stupid. Nike.
    • How much does the shifter move when the car is in gear with the engine off? If it is more than about 1cm you need to replace your shifter bush. Your shifts will just get crunchier, not faster, with a short shifter unless you also rebuild the whole box
    • I should video mine, will prob do it tomorrow    Between 1st and 3rd, you could fit another two gears. That is how loose and wobbly it is   horrible:(
×
×
  • Create New...