Jump to content
SAU Community

Car will not start but makes strange clicking noise - HELP


Recommended Posts

EDIT 3/8/05: Problem fixed for now - see post 12 below.

Been having a bad run with the line,

Had a minor bingle about 2 weeks ago, car was running fine after (only front bumper was rooted) so the car was sitting in my garage and not started for 1 1/2 weeks. Go to start it yesterday and battery was dead, no prob, it was on the way out for a while and I already had a new one. So I replace the battery and go to start it and when I hold the key in the start position I get this loud Click, Click, Click, Click, Click, Click, noise at about 5 Hz, comming from the somewhere up front. The motor does not turn over at all.

When I hold start the voltage drops considerably - I know the battery is good, besides I also tried to start the car with the car jumpered to another running car.

All this sounds like a rooted starter motor to me, but before I spend craploads on a mechanic trying to find out what is wrong - has anyone had a similar problem? Does anyone know what it couls be?

Any help greatly appreciated.

Link to comment
Share on other sites

i had the same problem iwth mine when i imported the r32. i thought it was the alternator but when i took it to the auto electrican he found out the it was some weird fuse ive never heard of before or something. if i were you i would take it to the auto electrician. get him to ring you once he knows what the problem is then you can decide from there. im a cheap arse and if it was the alternator i would have bought a second hand one instead of paying a shitload for a new one

Link to comment
Share on other sites

mine does that every so often, i just thought there wasn't enougfh power to run the starter motor properly and sounded like a clutch like device was clicking away, dunno, a quick push and off we went, starts properly now

Link to comment
Share on other sites

It seems to be a problem in the starter circuitry. When I had that problem, my mech re-wired the starter solenoid so it got power direct from the battery (used the factory trigger wire to switch a relay). Haven't had a problem since.

Link to comment
Share on other sites

I have had the same issue, but mine did it also when there was plenty of voltage (seen from PFC). I always figured the starter motor was not engauged right. All I do to fix the issue is move the car a little while in gear the the problem goes away.

I dont know if I am right with my theory but it works for me...

Link to comment
Share on other sites

I thought of doing that but then I thought that the startor mortor is not engaged unless it is being cranked. I'll give it a go if it worked for you.

I have had the same issue, but mine did it also when there was plenty of voltage (seen from PFC). I always figured the starter motor was not engauged right. All I do to fix the issue is move the car a little while in gear the the problem goes away.

I dont know if I am right with my theory but it works for me...

Link to comment
Share on other sites

I have had the same issue, but mine did it also when there was plenty of voltage (seen from PFC). I always figured the starter motor was not engauged right. All I do to fix the issue is move the car a little while in gear the the problem goes away.

I dont know if I am right with my theory but it works for me...

Mine does the exact same thing.. a couple of times a week I have to give it a bit of a clutch start..

Link to comment
Share on other sites

That clicking noise is the noise that it will make when the battery cannot supply enough CCA to the starter motor (Cold Cranking Amps). It makes this when enough voltage is present to turn the vehicles circuitry on but not enough to crank the motor. Check your battery voltage and then if that doesnt work get your wiring to your starter motor checked. If the starter motor was rooted I doubt it would even make a clicking noise.

Link to comment
Share on other sites

I seem to have fixed the problem, I just played around with the power connections to the starter motor and gave them a quick cleen - have not had a problem since (3 days later).

Thanks all for your help, if this fourm did not exist I may have payed $200 for someone in a workshop to do the same thing.

Cheers,

Pat.

Link to comment
Share on other sites

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stop on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, you need to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
    • @99RS4just wondering if you ever took photos of the footwell lighting / how you bypassed the controller, im keen to haver footwell lighting come on when I open the doors too   
    • Ultimately, if the tip is not far into the runner and the o-ring seals, then you are in business. Have you applied pressure to it as is? It is not really a problem for the injector to twist once it is bolted down, the oring seals it and you don't want it jambed into the oring too hard The plenum is intended to take multiple size lower injectors with different adapters, but the way you have it is fine if they seal.
    • Are these the Dmax ones you are in reference too? https://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35#description Not a bad idea to get the uni flange ones. I have sent just jap an email too. Will see what they say lmao. Only thing is the Dmax ones are on a big back order. Low key anything will be better then my OEM ones I got as they are sounding like popcorn when I go under load lmao 😂☠️🪦.
×
×
  • Create New...