Jump to content
SAU Community

Drift Day At Collie An Alternative


Steve
 Share

Recommended Posts

  • Replies 116
  • Created
  • Last Reply

Top Posters In This Topic

Anyone thinking about considering a location and time to meet so all the competitors can travel down at the same time? Only suggesting because it is a very very long trip to get down there and some of us aren't familar how to get to collie or where we are supposed to meet as well.

Maybe a meet point say at Maccas for breakfast and then heading down south all at the same time? Comments?

Link to comment
Share on other sites

Anyone thinking about considering a location and time to meet so all the competitors can travel down at the same time? Only suggesting because it is a very very long trip to get down there and some of us aren't familar how to get to collie or where we are supposed to meet as well.

Maybe a meet point say at Maccas for breakfast and then heading down south all at the same time? Comments?

Im in for sure.

Link to comment
Share on other sites

Alright well considering the response.. I might have a crack at trying to make a cruise and see how I go.

Closer to the date once I get more details I will post up a time but the meetpoint will be at Leach Hwy Macca's in Myaree as it is far enough south and close to the freeway onramps to make it an easy location for most people.

Link to comment
Share on other sites

XRW, yep, got you down + 1 already.

Josh, at this stage, probably only one day. I did leave it open and book the whole weekend, but it seems most dont want the two days.

Without the numbers, it would get very expensive for people on the sunday, unfortuneately.

Link to comment
Share on other sites

also is there a bp down there for ultimate? otherwise its jerry can time

The circuit is easy to find.

Drive through Collie (Towards Darkan) and keep going until you will see a sign for the motorplex at the bottom of the hill a few kms out from Collie. Turn right. Then it is left at the next tee junction and the circuit is a couple of km's further down on your right.

There is no 98 Octane in Collie. Best bet is to fill up in Pinjarra & also bring a jerry can.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stop on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, you need to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
    • @99RS4just wondering if you ever took photos of the footwell lighting / how you bypassed the controller, im keen to haver footwell lighting come on when I open the doors too   
    • Ultimately, if the tip is not far into the runner and the o-ring seals, then you are in business. Have you applied pressure to it as is? It is not really a problem for the injector to twist once it is bolted down, the oring seals it and you don't want it jambed into the oring too hard The plenum is intended to take multiple size lower injectors with different adapters, but the way you have it is fine if they seal.
    • Are these the Dmax ones you are in reference too? https://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35#description Not a bad idea to get the uni flange ones. I have sent just jap an email too. Will see what they say lmao. Only thing is the Dmax ones are on a big back order. Low key anything will be better then my OEM ones I got as they are sounding like popcorn when I go under load lmao 😂☠️🪦.
×
×
  • Create New...