Jump to content
SAU Community

Recommended Posts

I need to upgrade the wiring to my fuel pump so I can run the standard gtr pump @ close to 14v

Does anyone have any detailed pictures of how to do it?

I understand i need to put in new wiring + relay and fuse and have this connected direct to the fuel pump

Does this mean i need to physically remove the fuel pump and connect the new wiring direct to the pump itself, and put a hole through the grommet and all the other stuff ? Do i need to cut one of the wires leading into the nissan typical 5 plug and connect it to the relay

I would really appreciate any help, because i need to get this done by tuesday

Cheers

Link to comment
https://www.sau.com.au/forums/topic/83118-fuel-pump-relay/
Share on other sites

Guest two.06l
I need to upgrade the wiring to my fuel pump so I can run the standard gtr pump @ close to 14v

Does anyone have any detailed pictures of how to do it?

I understand i need to put in new wiring + relay and fuse and have this connected direct to the fuel pump

Does this mean i need to physically remove the fuel pump and connect the new wiring direct to the pump itself, and put a hole through the grommet and all the other stuff ? Do i need to cut one of the wires leading into the nissan typical 5  plug and connect it to the relay

I would really appreciate any help, because i need to get this done by tuesday

Cheers

Tommyk....ring me and ill step you through it mate....02 49847847

Paul

DIRTgarage

Link to comment
https://www.sau.com.au/forums/topic/83118-fuel-pump-relay/#findComment-1504292
Share on other sites

Measure the voltage at the fuel pump before you bother.

The OEM fuel pump relay is in the boot near the battery. There is less than 1m cable between the fuel pump and the battery.

The voltage drop over that length should be negligible...I'll explain why.

Assume the OEM cable has a cross sectional area of 1mm squared (it's actually much thicker)

Assume 1m cable

Assume resistivity of copper is 0.0000000168nΩm at room temp

Now, resistance of the 1m cable = resistivity x length / area

= 0.0000000168nΩm x 1m / (1/1000000)m

= 0.0168Ω

Now, voltage drop is given by current x resistance

Assume the fuel pump draws 10A (should be a bit less)

Voltage drop = 10 x 0.0168 = 0.168V

Which is next to nothing

Soemone please correct me if I'm made any errors

Link to comment
https://www.sau.com.au/forums/topic/83118-fuel-pump-relay/#findComment-1506869
Share on other sites

Thats correct Mik, however the high low resistor is what causes the fuel pump not to receive the full volts when under load.

Unsure why that is my understanding.

Running a dedicated power feed does indeed help.

I'll be grabbing the multimeter and checking mine out. I run an external and internal pump, both of those running flat stick must be drawing quite a few amps, hence my reason to upgrade the wiring to a minimum of 30amp stuff.

Link to comment
https://www.sau.com.au/forums/topic/83118-fuel-pump-relay/#findComment-1506874
Share on other sites

I have run dedicated 30 amp wiring with a 20 amp fuse for my external pump (044). A relay is triggered off the factory power feed to the intank pump. The intank pump (walbro) is still running off the factory wiring through the stock 10amp fuse with no problems.

I also run a surge tank with the return line feeding back into the top so the 044 is effectively feeding itself once primed if the walbro cant keep up.

Only problem i have is the PFC doesn't prime the pump long enough for the 044 to build up rail pressure so i have to turn the car to reds, then off, then back on before cranking.

Link to comment
https://www.sau.com.au/forums/topic/83118-fuel-pump-relay/#findComment-1506992
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Breather for it. If it's anything like the GTRs it should run up to the top of a bellhousing bolt.
    • What basics? With these OBD1 ECUs it's not like the ECU will give you any real clues, it's not really doing any sanity checking of sensors/sensor data. My experience is actually a lot of sensors tend to be the source of the issue first and foremost, and checking everything gives you a direction to investigate. MAF/O2/STFT/LTFT should all kind of make sense. You can try little tricks of the trade like tapping the MAFs to see if it triggers a stumble, things like that. But once you've done a compression test knowing whether you have an air leak or fuel delivery problem is kind of hard to narrow down without sensor data. And you don't really know if all your sensors are making sense unless you can interrogate the ECU directly about what it's seeing for sensor data.
    • Absolutely this. Yes, except not vacuum hose. Something oil/fuel safe is a better idea.
    • Like a Stagea, but not as cool! Hope you have enough garage space for this, or is something going to leave to make way for it?
    • The new project has arrived. I have wanted one of these for such a long time, well before that meathead Clarkson drove one in Africa. I really wanted an E34 but I have some medical issues that mean I *really* can't bump my head and the lack of airbags in the E34 made it just too big of a risk.  I don't know why I've always liked these older touring BMW's to be honest, but man I love this car. She's been pretty well maintained for her 243k's with what appears to be only a single oil leak at the oil filter housing gasket. It has a bunch of updates including later model bumper and headlights, 7 series billion-way adjustable seats and it came with a few spares and another set of wheels with legal tyres. I got a unregistered car permit from the RTA and drove it back from Canberra on Saturday.                   First cab off the rank is cleaning it up for blue slip. I dont know how picky they'll be but I figured I'd clean the headlights, fix the oil filter housing gasket, replace the speed sensors (throwing errors) and swap the OE wheels (the M Sport wheels have a big chunk out of one of the tyres.) I also need to replace all 6 gas struts - 2 for bonnet, 2 for hatch and 2 for hatch glass. The car tries to eat me whenever i open any of these. My plan for this car; Ultimately, this is a budget car. I can't afford to throw lots at it and its because I have another car that I got this, if something breaks its no big deal. I will just maintain and repair it really. But eventually I want to do a manual conversion. It actually looks pretty straight forward for E39's and the trickiest part will be sourcing the parts.  I do need to replace some suspension arms or bushes because wow, she's a floaty old girl. She's also fantastically slow. Like really, really slow. When pulling back out on to the freeway on Sat after a quick pull over I needed to wait until no cars were visible before going.  Oh, and the guy I bought it from had a gorgeous R31 GTS-X in the garage. 
×
×
  • Create New...